manualshive.com logo in svg

Empire Comfort Systems Tahoe DVP36PP32EN-1, Инструкция по установке и руководство пользователя, Страница: 45 / 64

Поделиться
Скачать
Empire Comfort Systems Tahoe DVP36PP32EN-1 Скачать руководство пользователя страница 45

24325-0-0708

Page 45

Placement of the glowing embers (rockwool) is very individual and 

light coverage of the areas indicated will provide your best effects. 

We recommend separation of the rockwool by hand and to make 

your coverage as light and fluffy as possible.
Place just enough embers on the burner to obtain the glow and a 

gold yellow flame.
Do not place rockwool over large port areas. 
Rockwool should not be placed in the area of the pilot assembly.
Over time, the rockwool will break down and new rockwool will 

need to be placed to recreate the original glowing embers effect. 

Remove  all  old  rockwool  from  the  appliance  and  apply  new 

rockwool as shown in Figure 63. 
Note:  Only  the  rockwool  supplied  with  this  unit  or  ordered  in 

accordance  with  the  Parts  List  on  page  53  should  be  used  on 

this burner. See the Parts List on page 53 to order replacement 

rockwool. 
Optional Platinum Embers (PE-20-1) may also be used with this 

fireplace. Contact your dealer for availability.

PLACEMENT OF GLOWING EMBERS

Place ember material only

over port areas as shown

Do not cover any large ports with

ember material (glowing embers)

TOP VIEW

Figure 63

Содержание Tahoe DVP36PP32EN-1

































































Отзывы:

Нет отзывов