manualshive.com logo in svg

Empire Comfort Systems Tahoe DVP36PP32EN-1, Инструкция по установке и руководство пользователя, Страница: 16 / 64

Поделиться
Скачать
Empire Comfort Systems Tahoe DVP36PP32EN-1 Скачать руководство пользователя страница 16

24325-0-0708

Page 16

Locating Fireplace

Place fireplace in framed opening. Attach the framing brackets to 

the fireplace and secure to framing. Different hole locations can 

be used for finishing materials with thicknesses of 3/8", 1/2" and 

3/4". Secure the brackets with screws provided using two (2) per 

framing bracket. 

See Figure 13.

Framing brackets should fit directly against framing material. Use 

at least one (1) nail or screw per bracket to secure in place.

IMPORTANT!

 Check squareness of  all openings of the fireplace 

prior to securing to the framed openings. 

See Figure 14.

NOTE: 

On See-Through models, framing brackets may be placed 

on one side of the facing openings. This allows the fireplace to be 

inserted into the pre-framed opening.

Figure 13

CHECK TO SEE

THAT BOX IS SQUARE

PRIOR TO ATTACHING TO

FRAMING

FIREPLACE OPENING

Figure 14

FIREPLACE INSTALLATION INSTRUCTIONS (continued)

ATTACH (4)

FRAMING BRACKETS

TO SIDE(S) OF FIREPLACE

PRIOR TO INSTALLING

UNIT TO FRAMED OPENING

Содержание Tahoe DVP36PP32EN-1

































































Отзывы:

Нет отзывов