Empire Comfort Systems Tahoe DVP36PP32EN-1 Скачать руководство пользователя страница 18

Страница: 18 / 64

24325-0-0708

Page 18

Figure 18

Vent Pipe Clearance

Note:

Maintain one inch (1") of clearance around vertical vent

pipe.

See Figure 18.

For horizontal vent, maintain a minimum 1"

clearance to the bottom and sides of the vent, and 3" clearance to

combustibles above the vent pipe.

See Figure 19.

VENT PIPE

1” MINIMUM CLEARANCE

AROUND VENT PIPE

Top of Vent

3” (76mm)

1” (25mm)

6 5/8” Diameter - Hard Pipe
7” Diameter - Flex Pipe
intake vent

4” Diameter flue

Combustibles NOT
allowed in shaded
area

Figure 19

Combustible Surround Installation

Figure 17

Attention: Cold climate installation recommendation: When

installing this unit against a non-insulated exterior wall, it is

recommended that the outer walls be insulated to conform

to applicable insulation codes.

Vent Runs

In planning the installation for the ﬁreplace, it is necessary to install

certain components before the appliance is completely positioned

and installed. These include the direct vent system, gas piping for the

appliance and the electrical wiring. (If the fan option is used.)
In addition to non-combustible surfaces, the appliance can be

mounted on any of the following surface options:

1. A ﬂat, hard combustible (burnable) surface.

2. A raised wooden platform.

3. Four (4) corner supports. (Example: Four (4) concrete masonry

blocks.) These supports must be positioned so they contact all

four (4) perimeter edges on the bottom of the unit.

FINISHED WALL

COMBUSTIBLE SURROUND

MANTELSHELF

2 X 4
HEADER

STAND OFF

6 3/8” OF NON-COMBUSTIBLE
MATERIAL

FRONT TRIM OR
NON-COMBUSTIBLE
MATERIAL (INSTALLATION
IS OPTIONAL)

JOINT BETWEEN FINISHED
WALL AND UNIT SEALED WITH
300°F (149°C) SEALANT MATERIAL
(SEALANT IS OPTIONAL)

Содержание Tahoe DVP36PP32EN-1

































































Результаты поиска

Содержание Tahoe DVP36PP32EN-1

Отзывы:

Empire Comfort Systems Tahoe DVP36PP32EN-1, Инструкция по установке и руководство пользователя, Страница: 18 / 64

Результаты поиска

Содержание Tahoe DVP36PP32EN-1

Отзывы: