Empire Comfort Systems DVCC32BP30N-2 страница 46 Скачать руководство пользователя

Страница: 46 / 56

35919-4-1015

Page 46

CAUTION

ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRI

CIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL,

CITY AND STATE BUILDING CODES. BEFORE MAKING

THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN

POWER SUPPLY IS DISCONNECTED. THE APPLIANCE,

WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN

ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE

OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE

ANSI/NFPA 70 (LATEST EDITION).

A factory installed junction box is located on the lower right side of

the fireplace. Wiring must be fed to the junction box and attached

to the receptacle that is provided. Leave approximately 6-in of wire

in the junction box for connection.

Attach black wire to one side of the receptacle and white wire to

opposite side of receptacle. The ground wire should be attached

to the green (ground) screw.

Install the receptacle into the junction box. Attach cover plate.

Note:

IP units have two junction boxes.

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

BLACK (HOT)

BRASS SCREWS

JUNCTION BOX

WHITE (NEUTRAL)

GROUND

SILVER SCREWS

GREEN SCREWS

110 VOLT POWER SUPPLY

JUNCTION BOX CONNECTIONS

Figure 74

Содержание DVCC32BP30N-2

























































Результаты поиска

Содержание DVCC32BP30N-2

Отзывы:

Похожие инструкции для DVCC32BP30N-2

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCC32BP30N-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVCC32BP30N-2

Отзывы:

Похожие инструкции для DVCC32BP30N-2

Бренды по названию

Популярные бренды