Empire Comfort Systems DVCC32BP30N-2 страница 38 Скачать руководство пользователя

Страница: 38 / 56

35919-4-1015

Page 38

IPI ELECTRONIC SYSTEM OPERATING INSTRUCTIONS (BP7 SERIES)

5.25 VDC ELECTRONIC CONTROL VALVE

The electronic control valve system includes the ability to switch

the pilot from a standing pilot mode to an intermittent pilot mode.

•

IPI Mode

- In the Intermittent Pilot mode, when the unit

is turned ON, it will cause spark to the pilot, light the

pilot, then allow the burner to light. When the unit is

turned to OFF, both the burner and pilot will be OFF.

•

CPI Mode

- In the Continuous Pilot mode, the pilot

remains ON continuously even when the burner is

turned OFF.

Note: A small toggle switch is located on the front of the module

tray that is used to switch from IPI (left) to the CPI (right).

See Figure 71.

When the unit is turned to ON, the electrical current will energize

a spark to the pilot igniter. Once the pilot sensor heats up (after a

few seconds), the valve will be energized, allowing gas to flow to

the burner.

1. Follow the SAFETY and LIGHTING INSTRUCTIONS for

Intermittent Pilot controls found in this manual, and on labels

found in the control compartment located in the lower cavity

of the appliance.

2. During the heating season (or in power outage periods), it is

recommended that the pilot remain in the CPI (standing pilot

mode) to reduce cold start issues, and/or conserve battery

backup power during a power outage.

3. The gas valve has inlet and outlet pressure taps as shown

Figure 71.

Refer to pages 15 and 16 for gas pressure

requirements.

Note:

The gas control has a manual HI/LO flame adjustment

knob (regulator) that allows you to increase or decrease

the height of the burner flame.

See Figure 69.

Rotate

the HI/LO knob counterclockwise to “HI” to increase

the flame height, and clockwise to “LO” to decrease the

flame height.

OPTIONAL REMOTE CONTROLS

Optional remote controls are available for use with this appliance.

It is recommended that the remote receiver be placed either

in a wall outlet box with extended wiring, or in the control

compartment area as far forward as possible.

The placement options for the remote receiver are given to allow

flexibility, however battery life will be extended when the receiver

is placed in cooler areas.

To connect the remote receiver to the appliance, first disconnect

the ON/OFF switch wires from the white and green wire

connectors and connect the wires from the remote receiver to the

green and white wire connectors.

See Figure 71.

Follow the instructions included with the remote control for

programming and other operational information.

IGNITOR

SENSOR

PILOT
ASSEMBLY

MANUAL
HI/LO
REGULATOR

GAS VALVE

OUTLET
PRESSURE
TAP

INLET
PRESSURE
TAP

MODULE TRAY

9 PIN CONNECTOR

SPARK ROD

GROUND

MANUAL ON/OFF SWITCH
NOTE: ADDITIONAL ON/OFF SWITCH & WIRING INCLUDED

PILOT SELECTOR SWITCH

IPI - INTERMITANT PILOT (LEFT)
CPI - CONTINUOUS PILOT (RIGHT)

AA (4)
BATTERY
BACKUP

Figure 69

Содержание DVCC32BP30N-2

























































Результаты поиска

Содержание DVCC32BP30N-2

Отзывы:

Похожие инструкции для DVCC32BP30N-2

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCC32BP30N-2, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVCC32BP30N-2

Отзывы:

Похожие инструкции для DVCC32BP30N-2

Бренды по названию

Популярные бренды