Empire Comfort Systems Boulevard MULTIFUNCTION REMOTE DVLL48SP Скачать руководство пользователя

Страница: 54 / 66

37754-6-1019

Page 54

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance must be lighted with the remote control.

When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING, smell around the appliance area

for gas. Be sure to smell next to the floor because

some gas in heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions. If you cannot reach your gas

supplier, call the fire department.

C. Use only the remote control to operate the valve.

Never use tools. If valve does not operate, don't try to

repair it, call a qualified service technician. Force or

attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been

underwater. Immediately call a qualified service

technician to inspect the appliance and to replace any

part of the control system and any gas control which

has been underwater.

LIGHTING INSTRUCTIONS

1. Turn off all electric power to the appliance if service is

to be performed (if applicable).

2. Locate On/Off gas shut-off and turn clockwise to

OFF. Do not force.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Turn OFF electric power to the appliance.

3. Turn gas shut-off counterclockwise

to ON

position.

4. Wait ten minutes to clear out any gas. Then smell for

gas, including near the floor. If you smell gas, STOP!

Follow B in the safety information above on this label. If

you do not smell gas, go to the next step.

5. Turn ON electric power to the appliance.

6. Using the remote control, turn main flame to ON. Refer

to the Multifunction Remote Operating Instructions for

more information. If the pilot does not light within 60

seconds, stop and go back to Step 4.

7. Refer to remote control instructions for detailed

information, control features, and operation. Note:

Refer to Multifunction Remote operating instructions

for selection of continuous standing pilot mode or

intermittent pilot mode. If the pilot or burner does

not stay lit (in the continuous pilot mode), stop and

immediately call a qualified service technician or gas

supplier.

8. If the burner or pilot does not operate properly after

several tries, turn the gas control knob clockwise

to OFF and call your service technician or

gas supplier.

9. Operation of the gas valve, blower, and/or optional

light must be controlled by using the hand held remote

control. Refer to remote instructions for detailed

operation information.

WARNING

If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

personal injury, or loss of life.

TO TURN OFF GAS TO APPLIANCE

GAS SHUT-OFF VALVE

Содержание Boulevard MULTIFUNCTION REMOTE DVLL48SP



































































Результаты поиска

Содержание Boulevard MULTIFUNCTION REMOTE DVLL48SP

Отзывы:

Похожие инструкции для Boulevard MULTIFUNCTION REMOTE DVLL48SP

Бренды по названию

Популярные бренды

Empire Comfort Systems Boulevard MULTIFUNCTION REMOTE DVLL48SP, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание Boulevard MULTIFUNCTION REMOTE DVLL48SP

Отзывы:

Похожие инструкции для Boulevard MULTIFUNCTION REMOTE DVLL48SP

Бренды по названию

Популярные бренды