background image

40397-1-0719

Page 5

IMPORTANT SAFETY INFORMATION

INSTALLER:

 Leave these instructions with the owner. For 

Installation In Solid Fuel Burning Fireplaces. Do not burn wood 

or solid fuels in a fireplace where a decorative gas log set is 

installed. This appliance is for installation only in a solid fuel 

burning fireplace, masonry fireplace or manufactured fireplace.

WARNING

Before installing in a solid fuel burning fireplace, the chimney 

flue and firebox must be cleaned of soot, creosote, ashes 

and loose paint by a qualified chimney cleaner.

WARNING

Do not allow fans to blow directly into or at the fireplace. 

Avoid any drafts that alter burner flame patterns.

WARNING

Do not use a blower insert, heat exchanger insert or other 

accessory not approved for use with this appliance.

DANGER

Any modification to this gas log set or to controls can be 

dangerous. Improper installation or use of the gas log set 

can cause serious injury or death from fire, burns, explo

-

sion or carbon monoxide poisoning.

WARNING

Do not operate this burner with glass doors closed. 

• 

Installation and repair must be done by a qUALIFIED 

SERVICE PERSON. The appliance should be inspected 

before use and at least annually by a qualified service 

person. More frequent cleaning may be required due to 

excessive lint from carpeting, bedding materials, etc. It 

is imperative that control compartments, burners and 

circulating air passageways of the appliance be kept clean.

• 

Dot not place clothing or other flammable material on or near 

the appliance.

• 

Do not place trash or other articles on the log set during 

operation.

• 

Do not put anything around the fireplace that will obstruct the 

flow of ventilation air.

• 

Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 

appliance and to replace any part of the control system and 

any gas control which has been under water.

• 

Do not use thermostats on vented burner applications 

 

Keep the appliance area clear and free from combustible 

material, gasoline and other flammable vapors and liquids.

• 

Keep burner and control compartment clean. 

• 

A yearly examination and cleaning of the venting system 

of the solid-fuel burning fireplace must be performed by a 

qualified agency.

• 

Make a periodic visual check of pilot and burners. Clean and 

replace damaged parts.

• 

Alert children and adults to the hazards of high surface 

temperatures and caution them to stay away to avoid burns 

or clothing ignition.

• 

Carefully supervise young children when they are in the 

same room as the appliance.

• 

During manufacture, this burner is treated with certain oils, 

films and bonding agents. These substances are not harmful 

but may produce smoke and odors as they burn off during 

initial operation of the fireplace. This is normal. Open a 

window during the initial bake out period. 

• 

Proper installation, burner pan location and log placement 

is important to achieve optimum look and performance of 

your gas log set. Follow the log assembly sequence for 

proper operation.

• 

Do not operate this log set with glass doors in the closed 

position. A fireplace screen must be in place when the log 

set is burning. Adequate combustion air must be provided for 

proper venting. All flames should go up and out the top of the 

firebox into the flue vent. If any flames float or curl forward 

into the room do not operate appliance. Check for an open 

flue and adequate combustion air into the room. A damper 

clamp must be installed on the firebox damper to maintain 

an open flue. See page 10.

• 

Young children must be carefully supervised when they are 

in the same room as the gas log while in operation. Do not 

place stockings, clothing or any flammable material above or 

near the fireplace.

• 

Do not substitute or use materials other than those supplied 

for use with the log set.

WARNING

Follow all gas leak check procedures in this manual, prior 

to operation.

WARNING

Fuels used in gas or oil-fired appliances, and the products 

of combustion of such fuels, contain chemicals known to 

the State of California to cause cancer, birth defects, and/

or other reproductive harm. This warning is issued pursu-

ant to California Health & Safety Code Sec. 25249.6.  

DO NOT ATTEMPT TO DISCONNECT THE GAS OR ANY GAS 

FITTING WHILE THIS APPLIANCE IS IN OPERATION.
NEVER leave the decorative gas log set unattended while in 

operation.
NEVER allow children to operate this decorative gas log set.

NEVER place hands or fingers on the front-edge of this 

decorative gas log set.

NEVER use liquid propane gas in a natural gas unit, or natural 

gas in a liquid propane unit.

DO NOT use solid-fuel or lighter fluid in any decorative gas log set.

Any safety screen or guard removed for servicing an appliance 

must be replaced prior to operating the appliance.

Содержание BFE2124MTN





























Отзывы: