EmmeGas READY OBD Скачать руководство пользователя страница 8

616000114 - Rev. 200513-0

15-25

Il presente documento non può essere riprodotto né portato a conoscenza di terzi senza autorizzazione della ditta EMMEGAS

This document may not be reproduced or made known to any third party without permission of the company EMMEGAS

616000114 - Rev. 200513-0

14-25

Il presente documento non può essere riprodotto né portato a conoscenza di terzi senza autorizzazione della ditta EMMEGAS

This document may not be reproduced or made known to any third party without permission of the company EMMEGAS

3 CYLINDER CAR WIRING DIAGRAM

DESCRIPTION OF THE CONNECTIONS MADE ON THE OBD CONNECTOR

Connect a hand-held tester (CODE AEB214), and check the type of connection.

If the tester reads connection types 1,2, or 3, proceed by following the diagram in figure 1.

If the tester reads connection types 6,7,8 or 9, proceed by following the diagram in figure 2.

ATTENTION:

 If the tester (CODE AEB214) reads a type of connection that is not stated above, do 

not connect to any of the signals.

TYPE OF CONNECTION

CONNECTION DETAILS

Connection type 6

CAN Standard 250 Kbps

Connection type 7

CAN Extended 250 Kbps

Connection type 8

CAN Standard 500 Kbps

Connection type 9

CAN Extended 500 Kbps

Connect the GREEN wire to the signal found on PIN 7 of the OBD connector. 

ATTENTION:

 

The YELLOW-GREEN and YELLOW-GREY wires must be isolated and not connected.

PIN7

1

8

9

FIG.1

16

Connect the YELLOW-GREEN wire to the signal found on PIN 6 and the wire YELLOW-GREY to PIN 14 of the 

OBD connector.

ATTENTION:

 

The GREEN wire must be isolated and not connected

PIN6

1

8

9

FIG.2

16

PIN14

Through connection to the vehicle’s OBD socket, this new generation of GAS control units makes it possible to 

acquire information useful for properly setting up the vehicle.

Several carburetion parameters acquired from the PETROL control unit can be seen using the special software 

for connecting the GAS control unit to the PC, such as:

•  Carburetion calibrators (Fast and Slow).

•  Voltage on the rear lambda probe.

    

TYPE OF CONNECTION

CONNECTION DETAILS

Connection type 1

ISO 9141-2

Connection type 2

KWP-2000 Fast Init

Connection type 3

KWP-2000 Slow Init

OBD Connector 

seen frontal

OBD Connector 

seen frontal

GASOLINE

INJECTORS

COLLECTORS

OF ASPIRATION

DO NOT CONNECT

RAIL INJECTORS 

GAS 3 CYLINDER

PETROL INJECTOR 

ORIGINAL HARNESS 

CUT INJECTOR

WIRING

Содержание READY OBD















Отзывы: