Emerson Unidrive HS72 Скачать руководство пользователя страница 11

Страница: 11 / 46

Unidrive M702 / HS72 Control Getting Started Guide

Issue Number: 2

Safety inform

Introdu

Co
ntrol

Basic p

Runn

Encoder cable:

For best shielding use cable with an overall shield and individual shields on twisted

pairs, connect the cable as illustrated in Figure 3-4. Clamp the overall shield to grounded metallic
surfaces at both the encoder and the drive.

Brake resistor cable:

The optional braking resistor should also be wired with shielded cable. If

unshielded wire is required refer to the

Drive User Guide

for guidance.

Control cables:

If the control wiring is to leave the enclosure, it must be shielded and the shield(s)

clamped to the drive using the grounding bracket. Remove the outer insulating cover of the cable to
ensure the shield(s) make contact with the bracket, but keep the shield(s) intact until as close as
possible to the terminals.

Figure 3-4 Feedback cable shield connections

3.4

Control connections

For information on control connections, refer to the back cover of this guide.

Cable

Cable
shield

Twisted

pair

shield

Cable
shield

Twisted

pair

shield

Connection

at motor

Connection

at drive

Ground clamp

on shield

Shield

connection

to 0V

Shield

connection

to 0V

Unidrive M702_HS72 Control GSG Iss2.book Page 11 Friday, December 12, 2014 1:05 PM

Содержание Unidrive HS72















































Результаты поиска

Содержание Unidrive HS72

Отзывы:

Похожие инструкции для Unidrive HS72

Бренды по названию

Популярные бренды

Emerson Unidrive HS72, Руководство по началу работы с управлением

Результаты поиска

Содержание Unidrive HS72

Отзывы:

Похожие инструкции для Unidrive HS72

Бренды по названию

Популярные бренды