Emerson Unidrive HS72 Скачать руководство пользователя страница 16

Страница: 16 / 46

Unidrive M702 / HS72 Control Getting Started Guide

Issue Number: 2

4.3

Keypad operation

4.3.1

Control buttons

The keypad consists of:
•

Navigation Keys - Used to navigate the parameter structure and change parameter values.

•

Enter / Mode button - Used to toggle between parameter edit and view mode.

•

Escape / Exit button - Used to exit from parameter edit or view mode. In parameter edit mode, if
parameter values are edited and the exit button pressed the parameter value will be restored to
the value it had on entry to edit mode.

•

Start forward button - Use to provide a 'Run' command if keypad mode is selected.

•

Start reverse button - Used to control the drive if keypad mode is selected and the reverse button
is activated.

•

Stop / Reset button - Used to reset the drive. In keypad mode can be used for 'Stop'.

Figure 4-2 Display modes

The navigation keys can only be used to move between menus if Pr

00.049

has been set to show 'All

Menus'

To enter Edit Mode,
press

key,

Status
Mode

Parameter

Mode

Edit Mode

(Character to be edited in lower line of display flashing)

Change parameter values using

keys.

When returning
to Parameter
Mode use the

keys to select
another parameter
to change, if
required

To enter Parameter
Mode, press

key or

Temporary
Parameter
Mode

Timeout

To return to Status Mode,

parameter

R/W
parameter

To select parameter
Press

is displayed)

To return to Parameter Mode,
Press

key to keep the new parameter value

Press

key to ignore the new parameter value and return

the parameter to the pre-edited value

Press

key

Timeout

Press

key

(

Unidrive M702_HS72 Control GSG Iss2.book Page 16 Friday, December 12, 2014 1:05 PM

Содержание Unidrive HS72















































Результаты поиска

Содержание Unidrive HS72

Отзывы:

Похожие инструкции для Unidrive HS72

Бренды по названию

Популярные бренды

Emerson Unidrive HS72, Руководство по началу работы с управлением

Результаты поиска

Содержание Unidrive HS72

Отзывы:

Похожие инструкции для Unidrive HS72

Бренды по названию

Популярные бренды