Emerson Unidrive HS72 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 46

background image

14

Unidrive M702 / HS72 Control Getting Started Guide

Issue Number: 2

4. Select 'Save parameters in drive' to perform a parameter save.
The drive is now ready to run.

Action

Detail

Motor Setup

Unidrive M Connect contains a database for induction motors and permanent magnet motors.
Provision is also made to enter motor nameplate data.
The next section describes the use of the motor database for a Leroy Somer LSRPM motor
used in RFC-S Sensorless mode.

Motor Feedback
Setup

This only needs to be performed in RFC-A (with feedback) mode
Set Pr

03.024

= Feedback (0)

Enter:
•

Encoder power supply in Pr.

03.036

= 5 V (0), 8 V (1) or 15 V (2).

If output voltage from the encoder is >5 V, then the termination resistors must be
disabled Pr

03.039

to 0.

•

Drive encoder Lines Per Revolution (LPR) in Pr

03.034

(set according to encoder)

•

Drive encoder termination resistor setting in Pr

03.039

:

0

= A-A\, B-B\ termination resistors disabled

1

= A-A\, B-B\, termination resistors enabled

Analog I/O

The motor thermistor can be selected in Pr

07.015

. Refer to the parameter help for Pr

07.015

for further information.

Ramps Setup

Enter the required Acceleration rate and Deceleration rate
Note: If a braking resistor is installed, set 'Ramp mode' to 'Fast'. Also ensure Pr

10.030

and

Pr

10.031

and Pr

10.061

are set correctly, otherwise premature 'Brake R Too Hot' trips may

be seen).

Autotune

Not required when using data from the motor database for a Leroy Somer LSRPM motor used
in RFC-S Sensorless mode.

NOTE

Setting the encoder voltage supply too high for the encoder could result in
damage to the feedback device.

CAUTION

Unidrive M702_HS72 Control GSG Iss2.book Page 14 Friday, December 12, 2014 1:05 PM

«
...
12
13
14
15
16
...
»

Содержание Unidrive HS72















































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS72

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

Бренд: Gardner Denver Страницы: 22

Бренд: B&G Страницы: 2

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: Insignia Страницы: 2

Бренд: Purmo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды