Emerson Unidrive HS72 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 46

background image

12

Unidrive M702 / HS72 Control Getting Started Guide

Issue Number: 2

4

Getting started

4.1

Quick start commissioning / start-up using Unidrive M Con-

nect (V02.00.00.00 onwards)

Unidrive M Connect is a Windows™ based software commissioning / start-up tool for

Unidrive M/HS.

Unidrive M Connect can be used for commissioning / start-up and monitoring, drive parameters can be
uploaded, downloaded and compared and simple or custom menu listings can be created. Drive menus can
be displayed in standard list format or as live block diagrams. Unidrive M Connect is able to communicate
with a single drive or a network. Unidrive M Connect can be downloaded from www.controltechniques.com
(file size approximately 100 MB).

Unidrive M Connect system requirements

•

Windows 8, Windows 7 SP1, Windows Vista SP2, Windows XP SP3

•

Minimum of 1280 x 1024 screen resolution with 256 colours

•

Microsoft.Net Frameworks 4.0 (this is provided in the downloaded file)

•

Note that you must have administrator rights to install Unidrive M Connect

Any previous copy of Unidrive M Connect should be uninstalled before proceeding with the installation
(existing projects will not be lost). Included within Unidrive M Connect is the

Parameter Reference Guide

for

Unidrive M702/HS72.

4.1.1

Power-up the drive

1. Start Unidrive M Connect, and on the ‘Project Management’ screen select 'Scan serial RTU network' or

'Scan all connected drives’.

Unidrive M702_HS72 Control GSG Iss2.book Page 12 Friday, December 12, 2014 1:05 PM

«
...
10
11
12
13
14
...
»

Содержание Unidrive HS72















































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS72

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Datalogic Страницы: 15

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренд: K&K Страницы: 6

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

GRASS VALLEY MDX-3901

Бренд: Belden Страницы: 45

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Tristan Auron Страницы: 30

Бренд: Bard Страницы: 102

Бренд: Vestil Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды