Emerson Smart Wireless Gateway 1420 Скачать руководство пользователя страница 72

Страница: 72 / 96

Note

The coaxial cables on the remote antenna options WL3 and WL4 are interchangeable for
installation convenience.

A.7

Ordering information

Table A-1: Emerson Wireless 1420 Gateway Ordering Information

The starred offerings (

★

) represent the most common options and should be selected for best

delivery. The non-starred offerings are subject to additional delivery lead time.

Model

Product Description

1420

Smart Wireless Gateway

Power Input

24 VDC nominal (10.5-30 VDC)

★

Ethernet Communications - Physical Connection

(1)

(2)

Ethernet

★

(3)

(4)

Dual Ethernet

★

Wireless Update Rate, Operating Frequency, and Protocol

User configurable update rate, 2.4 GHz DSSS, WirelessHART

★

Serial Communication

None

★

(5)

Modbus RTU via RS485

★

Ethernet Communication - Data Protocols

Webserver, Modbus TCP/IP, AMS Wireless Configurator ready,
HART-IP

★

Webserver, Modbus TCP/IP, AMS Wireless Configurator ready,
HART-IP, OPC

★

(6)

DeltaV

™

ready

★

(6)

Ovation

™

ready

★

Webserver, EtherNet/IP, AMS Wireless Configurator ready,
HART-IP

★

Webserver, EtherNet/IP, Modbus TCP/IP, AMS Wireless
Configurator ready, HART-IP

★

Options (include with selected model number)

Product Certifications

U.S.A. Division 2

★

CSA Division 2, Non-incendive

★

(7)

ATEX Type n

★

(7)

ATEX Dust

★

Specifications and Reference Data

Reference Manual

September 2020

00809-0200-4420

Emerson.com/Rosemount

Содержание Smart Wireless Gateway 1420

































































































Результаты поиска

Содержание Smart Wireless Gateway 1420

Отзывы:

Бренды по названию

Популярные бренды

Emerson Smart Wireless Gateway 1420, Справочное руководство

Результаты поиска

Содержание Smart Wireless Gateway 1420

Отзывы:

Бренды по названию

Популярные бренды