Emerson Smart Wireless Gateway 1420 Скачать руководство пользователя страница 57

Страница: 57 / 96

Troubleshooting

6.1

Service support

Note

For more information see the Emerson Wireless Gateway User Interface Terminology

This section provides basic troubleshooting tips for the Emerson Wireless Field Network.
To receive technical support by phone:

Global Service Center Software and Integration Support

United States 1-800-833-8314 Interna63-2-702-1111

Customer Central Technical Support, quoting, and order related questions

United States 1-800-999-9307 (7:00 a.m. to 7:00 p.m. CST) Asia Pacific 65-6777-8211
Europe/ Middle East/Africa 49-8153-9390

Or email the wireless specialists at: [email protected]

North American Response Center

Equipment service needs

1-800-654-7768 (24 hours—includes Canada)

Outside of the United States, contact your local Emerson representative.

6.2

Troubleshooting Tables

Table 6-1: Troubleshooting Initial Connection

Issue

Troubleshooting steps

Web browser
returns page not
found

1. Connect the Gateway and PC/laptop.

2. Verify the Gateway is properly powered, 24 VDC (nominal) and 250 mA.

Open the upper cover and verify if any indicator lights are on.

3. Verify which Ethernet port is being used on the Gateway.

4. Verify the IP address for the Gateway (default primary port is

192.168.1.10, default secondary port is 192.168.2.10 or for DeltaV Ready
Gateway’s default primary port is 10.5.255.254, default secondary port is
10.9.255.254).

5. Verify the IP address of the PC/laptop is in the same subnet range as the

Gateway (i.e. If the Gateway IP is 155.177.0.xxx, then the PC/Lap IP
address should be 155.177.0.yyy).

6. Disable internet browser proxy settings.

Reference Manual

Troubleshooting

00809-0200-4420

September 2020

Emerson.com/Rosemount

Содержание Smart Wireless Gateway 1420

































































































Результаты поиска

Содержание Smart Wireless Gateway 1420

Отзывы:

Бренды по названию

Популярные бренды

Emerson Smart Wireless Gateway 1420, Справочное руководство

Результаты поиска

Содержание Smart Wireless Gateway 1420

Отзывы:

Бренды по названию

Популярные бренды