background image

1. Position the supply wires to the left side

of the outlet box (Figure 16); position
the fan wires to the right side. Partially
insert the remote control receiver (flat
side up) until one end rests on the
hanger ball as shown in Figure 16.

NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,

How to Wire

Your Ceiling Fan

Turning off wall switch is not suffi-
cient. To avoid possible electrical
shock, be sure electricity is turned
off at the main fuse box before
wiring. All wiring must be in accor-
dance with National and Local codes
and the ceiling fan must be properly
grounded as a precaution against
possible electrical shock.

!

WARNING

Check to see that all connections are
tight, including ground, and that no
bare wire is visible at the wire con-
nectors, except for the ground wire.
Do not operate fan until blades are in
place. Noise and fan damage could
result.

!

WARNING

If you feel that you do not have enough
electrical wiring knowledge or experi-
ence, have your fan installed by a
licensed electrician. 

including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
2. 
Refer to Figure 16 and 17 and connect

the receiver wires to the supply wires
and the fan motor wires as follows:

a. Securely connect the green grounding

wires from the hanger ball and the
hanger bracket to the supply grounding
conductor (this may be a bare wire or a
wire with green insulation).

b. Securely connect the supply white

(neutral) wire to the receiver white
(AC IN N) wire.

c. Securely connect the supply black wire

(hot) wire to the receiver black (AC IN
L) wire.

d. Securely connect the fan motor white

wire to the receiver white (TO MOTOR
N) wire.

e. Securely connect the fan motor black

wire to the receiver red (TO MOTOR L)
wire.

f. Securely connect the fan motor blue

wire to the receiver blue (FOR
LIGHT) wire.

GREEN GROUND 
WIRE FROM 
HANGER BRACKET

RECEIVER RED WIRE

RECEIVER WHITE WIRE

FAN WHITE WIRE

FAN 
BLACK 
WIRE

ANTENNA

AC IN N

AC IN L

FOR LIGHT

T

O

 MOT

OR N

RECEIVER BLUE 
WIRE

RECEIVER 
BLACK WIRE

RECEIVER WHITE 
WIRE

SUPPLY WHITE WIRE 
(NEUTRAL)

SUPPLY BLACK 
WIRE (HOT)

GROUND WIRE

GREEN GROUND 
WIRE FROM 
HANGER BALL

FAN BLUE WIRE

1-1/4" THREADED 
STUD (2)

T

O

 MOT

OR L

Figure 16

10

CAUTION: To reduce the risk of electri-
cal shock, disconnect the electrical
supply circuit before installing the fan,
light kit or receiver.

Emerson Structures  1/24/05  8:22 AM  Page 10

Содержание KF200NI00

















Отзывы: