V E N T
Fan-Tastic Vent
P.O. B o x 1 6 2 7 E l k h a r t , I N 4 6 5 1 5
PHONE: 800-521-0298 FAX: 800-201-4973
INTERNET: http://www.fantasticvent.com
]ntertek
4 0 0 4 7 / 8
Us
DOCUMENT PART NUMBER 8613-01
Fan-Tastic Vent Fans
& Controllers
Protected by U.S. Patents 7,731,574
and/or 7,731,249
Other Patents Pending
ENGLISH, FRANCAIS, (CANADA)
SAFETY INFORMATION
FOR YOUR SAFETY
READY ALL INSTRUCTIONS BEFORE OPERATING FAN
REFER TO )0000( FOR MODEL NUMBER
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
WARNING
avoid possible
injury or death
CAUTION
avoid possible injury
and/or property damage
RECOMMEND WIRE FOR POWER
SUPPLY:
A minimum of 16-gauge stranded copper
must be used. Insulated connectors must
be used.
WARNING ELECTROCUTION
• Disconnect power supply prior to installation.
INSTALLATION
WIRE COLOR CODE:
Black - Positive or Fused
White - Negative or Ground
ROOF MOUNTING INSTRUCTIONS: OEM (ORIGINAL EQUIPMENT MANUFACTURERS)
AFTERMARKET
Gasket or Sealer is required between mounting flange bottom & top of roof. Additional
compatible sealant over screws & at flange where it meets roof. Clamp fans; use a double
bead of compatible sealant only between the mounting flange and roof (No putty tape,
butyl or gaskets to be used with Clamp Fans). For rubber roofs use EPDM compatible roof
sealant, e.g. Dicor 551 LSW or 502 LSW.
RECOMMEND SCREWS:
No. 8 self-tapping flat head - 3/4" to 1" in length. All 16 holes must be used for proper
seal. After ceiling fan has been mounted and wired, install interior garnish with screws
provided. Garnish may be trimmed for thinner roofs. For deeper than standard garnish
call Fa n-Tastic Vent Toll Free. OEM Clamp fans require mounting screws and correct height
garnish pre-determined by OEM Customer and Fan-Tastic Vent. Torque all screws equally.
Do not over tighten.
FUSE: SYSTEM HAS BEEN FUSED BY FAN-TASTIC VENT. REPLACEMENT VALUE LABEL
ON FAN AT FUSE HOLDER. REPLACEMENT INSTRUCTIONS:
Locate the round black cap of the fuse holder (about the size of a dime) on the face of
the fan. Push up and quarter turn counter clockwise and pull down to expose the fuse.
Replace the old fuse with a new one and push in the fuse holder. Secure with clockwise
rotation of the cap. REPLACEMENT MUST BE SAME TYPE AND RATING.
REVERSE SWITCH MOUNTED ON THE FAN:
Units equipped with a reverse switch in the fan motor and fan blade must be completely
stopped before reversing fan.
BULB TYPE THERMOSTAT INSTRUCTIONS:
No additional external wiring.
NOTE:
A SAFETY SWITCH HAS BEEN INSTALLED ON THE UNIT, DOME MUST BE OPENED
APPROXIMATELY 3 INCHES BEFORE MOTOR WILL OPERATE. WHEN DOME IS SHUT
COMPLETELY, MOTOR WILL NOT OPERATE.
PERMANENT MAGNET MOTORS PERFORM AS DESIGNED ON FILTERED
OCCURRENT. UNFILTERED DC CURRENT MAY CREATE IRRITATING NOISE
FROM FAN BLADE MOTORS AND MAY CAUSE CIRCUIT BOARDS TO FAIL.
HOW TO USE YOUR FAN-TASTIC VENT'
Close all vents when using your Fan-Tastic Vents. Slightly open windows on shaded side
of coach afford the most comfortable ambient air, even on hot days. Remember, you
direct the airflow by opening a window. Always try to position yourself between an
open window and the fan for greatest airflow comfort.
Any installation or operating problems call Fan-Tastic Vent toll free immediately, (800)
521-0298
AUTOMATIC LIFT MOTORS
To manually open or close the lid on your Fan-Tastic Vent®, grasp the black hand knob and
turn in the direction desired. DO NOT PULL DOWN ON THE KNOB! Doing so may damage
your fan and/or cause physical injury.
PreviousFan-Tastic Vent Models used a two position (clutch) knob that required pulling
down to activate the manual feature. This new lift motor does not require any such
action.
