background image

WARNING: 

To avoid fire, shock, and serious personal injury, follow these instruc-

tions.

Safety Instructions

1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock serv-

ice panel disconnecting means to prevent power from being switched on acciden-
tally. When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan.

Always turn off the power to the ceiling fan before servicing.

4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned off at the fuse box before

wiring, and do not operate fan without blades.

2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA

70-1999 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.

3. The outlet box and joist must be securely mounted and capable of reliably sup-

porting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan
Support”, and use the mounting screws provided with the outlet box. Most outlet
boxes commonly used for support of light fixtures are not acceptable for fan sup-
port and may need to be replaced. Consult a qualified electrician if in doubt.

4. The longer downrod furnished with the fan provides the minimum recommended

floor to fan blade clearance for a 9 foot ceiling. The  6” downrod (supplied) must be
used for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7 feet from the floor to pre-

vent accidental contact with the fan blades.

6. Follow the recommended instructions for the proper method of wiring your ceiling

fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.

CAUTION: 

The halogen bulb operates at high internal pressure and high surface tem-

peratures and could shatter unexpectedly. The halogen bulb generates UV (ultraviolet)
radiation that may cause skin and eye irritation with prolonged exposure. To avoid
risks of burns or other injury, assure power is off before attempting to install or replace
halogen bulb. Do not operate fan/light without lower glass in place.
7. This fan uses a halogen bulb. Do not touch the bulb with bare hands. Fingerprints

may result in shorter bulb life. Remove fingerprints with alcohol.

NOTE:

This fan is suitable for use with solid-state speed controls.

WARNING: 

To reduce the risk of fire or electric shock, this fan should only be used

with fan speed control Model No. UL7067RC, manufactured by Rhine Electric Co., Ltd.

WARNING:

This product is designed to use only those parts supplied with this prod-

uct and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or property
damage.

WARNING: 

To reduce the risk of personal injury, do not bend the blade flange when

installing the blade flanges, balancing the blades or cleaning the fan. Do not insert for-
eign objects in between rotating fan blades.

!

WARNING

DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.

2

Emerson Structures  1/24/05  8:22 AM  Page 2

Содержание KF200NI00

















Отзывы: