Emerson GIE 4820/3A/3.45KW Скачать руководство пользователя страница 17

Страница: 17 / 44

Chapter 1 System Outline

GIE 4820/3A/3.45KW Power Supply System User Manual

Recommended Sensors

Signal

Port

Silk-sc

reen

Pin Functions

Factory

Model

Functions

Smoking

sensor port

SMOKE Pin 2 is +24V power, and

pin 1 is signal cable.

Shenzhen

Fanhai

Sanjiang

Electron Co.,

Ltd

JTY-LZ98

3K(HW)

Working in the detecting

workroom. When the fog grain

enters into the workroom, it will

output alarm current signal.

Once the sensor sends alarm,

its alarm state keeps all the

while. The current should be

cut off for recovering.

Gate

magnetic

sensor port

JTM1

Pin 2 is +24V power, and

pin 1 is signal cable. In the

default condition, the

shorting of pin 1 and pin 2

represents gate magnetic

normal, and the

disconnection represents

alarm. If the system do not

connect gate magnetic

sensor, the alarm can be

shielded by shorting pin 1

and pin 2 of the socket.

ALEPH

PS-1523

It can feel the open and close

of the door and send alarm. Its

technical specifications can

refer to the product manual.

Alarm dry

contact port

JK1,

JK2

The maximum voltage endurable is 60V

, the maximum load current is 500mA. When

there is a general alarm, Jk2 dry contact is shorting. When there is serious alarm, Jk1

dry contact is shorting. The level of the serious alarm and general alarm can be set

through the background software by users.

Opto-coupler

output port

JAC1,

JAC2

Pin 1 and pin 2 connects with C pole and E pole of opto-coupler separately, and the

parameters of the opto-coupler are Vcemax=40Vdc, Icmax=80mA. Pay attention to the

derating application.

Standby

digital value

input port

JTD1~J

TD7

Pin 1 o24V power, pin 2 o12V power, pin 3 is signal input, and pin 4

connects with grounding.

Users can connect correspond signal according to self-demanding, and can bring it into

the monitoring range after the simple configuration of the monitoring module.

The monitoring module of the system adopts hot-swappable design, and can be

replaced when the system is operating.

The address of the monitoring module can be set through the toggle switch on the

monitoring main board (eight digits, and four low bits are effective) to achieve the

centralized management of multi-power systems.

Содержание GIE 4820/3A/3.45KW













































Результаты поиска

Содержание GIE 4820/3A/3.45KW

Отзывы:

Похожие инструкции для GIE 4820/3A/3.45KW

Бренды по названию

Популярные бренды

Emerson GIE 4820/3A/3.45KW, Руководство пользователя

Результаты поиска

Содержание GIE 4820/3A/3.45KW

Отзывы:

Похожие инструкции для GIE 4820/3A/3.45KW

Бренды по названию

Популярные бренды