Emerson Fisher Vee-Ball V200U Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

background image

Instruction Manual

D104548X012

V200U Valve

May 2020

23

Parts Ordering

A serial number is assigned to each valve and stamped on the nameplate. Always refer to the valve serial number when
corresponding with your

Emerson sales office

regarding spare parts or technical information. When ordering

replacement parts, also specify the key number, part name, and desired material using the parts list.

WARNING

Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should
not, under any circumstances, be used in any Fisher valve, because they will void your warranty, might adversely affect the
performance of the valve, and could give rise to personal injury and property damage.

Retrofit Kits for ENVIRO‐SEAL Packing

Retrofit kits include parts to convert existing V200U valves with shallow (single packing depth) packing box to the
ENVIRO‐SEAL packing box construction. Retrofit kits include single PTFE packing. See following table.

ENVIRO‐SEAL Packing Retrofit Kits

SHAFT DIAMETER

(1)

PART NUMBER

mm

Inches

Single PTFE

Graphite

19.1

3/4

RRTYXRT0032

RRTYXRT0332

25.4

1

RRTYXRT0052

RRTYXRT0352

31.8

1‐1/4

RRTYXRT0062

RRTYXRT0362

Parts Included in Kit

Key

Description

Quantity

100

Packing stud

2

2

101

Packing nut

2

2

102

Packing flange

1

1

103

Spring pack assembly

1

1

105

Packing set

1

1

106

Anti-extrusion washer

2

‐ ‐ ‐

107

Packing box ring

(2)

1

1

‐ ‐ ‐

Tag

1

1

‐ ‐ ‐

Tie Cable

1

1

1. Diameter through the packing box.
2. Not required for all sizes of V150E with 1‐1/4 inch diameter shafts.

Repair Kits for ENVIRO‐SEAL Packing

Repair kits include valves parts for shallow (single packing depth) for ENVIRO‐SEAL packing box construction. Repair
kits include single PTFE or graphite packing. See following table.

ENVIRO‐SEAL Packing Repair Kits

SHAFT DIAMETER

(1)

PART NUMBER

mm

Inches

PTFE

Graphite

19.1

3/4

RRTYX000032

13B8816X052

25.4

1

RRTYX000052

13B8816X092

31.8

1‐1/4

RRTYX000062

13B8816X112

Parts Included in Kit

Key

Description

Quantity

105

Packing set

1

1

106

Anti‐extrusion washer

2

‐ ‐ ‐

(2)

1. Diameter through the packing box.
2. Included in key 105.

«
...
21
22
23
24
25
...
»

Содержание Fisher Vee-Ball V200U Series





























Отзывы:

Нет отзывов

Похожие инструкции для Fisher Vee-Ball V200U Series

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Canarm Страницы: 3

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: ISVT Страницы: 78

Бренд: Linear Technology Страницы: 8

Бренд: Precision Страницы: 8

TRAP-SHUFFLE Game Simulator

Бренд: RF SOLUTIONS Страницы: 2

Бренд: Water Specialist Страницы: 36

EXTA LIFE P-520

Бренд: Zamel Страницы: 10

Бренд: Watt Stopper Страницы: 3

SANTOKA 12.1 BX PCT

Бренд: Garz & Fricke Страницы: 37

Бренд: Zennio Страницы: 2

Бренд: rauland Страницы: 4

Бренд: Stephan Страницы: 42

Бренд: FONESTAR Страницы: 2

Бренд: ICP DAS USA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды