Emerson Fisher POSI-SEAL A31A Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 28

background image

Instruction Manual

D500242X012

A31A Cryogenic-Rotary Valve

February 2019

21

13. After driving the taper key in place, arc spot weld the head of the taper key to the disk. For valve sizes 8‐, 10‐ and

12‐inch, use an arc spot weld bead of 3/16‐inch in diameter.

14. Install the packing as described in the Packing Replacement section.

Installing the Gasket Retainer

Valves with a two‐piece shaft use a gasket retainer and gasket to cover the follower shaft opening in the valve body.

1. Replace the gasket (key 15) and gasket retainer (key 14) over the end of the follower shaft. Use a new gasket.

2. Replace the four hex head bolts (key 21) and lockwashers (key 20) to hold the gasket retainer in place.

3. Be sure to center the gasket over the follower shaft bore before retightening the bolts. Tighten down the bolts

evenly in a crossover or star pattern. Refer to table 5 for proper torque values.

«
...
19
20
21
22
23
...
»

Содержание Fisher POSI-SEAL A31A





























Отзывы:

Нет отзывов

Похожие инструкции для Fisher POSI-SEAL A31A

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: QCON Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Harsco Industrial Страницы: 57

Бренд: Van Air Страницы: 4

Бренд: Sanhua Страницы: 3

Бренд: Magnescale Страницы: 3

XP-9 88-IoT Series

Бренд: ICP DAS USA Страницы: 8

Бренд: ICON Страницы: 2

Бренд: ICP DAS USA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды