Emerson Fisher POSI-SEAL A31A Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

background image

Instruction Manual

D500242X012

A31A Cryogenic-Rotary Valve

February 2019

16

Figure 6. Anti‐Blowout Protection Detail

PACKING
FLANGE

ANTI‐BLOWOUT
FLANGE

SHAFT SHOULDER

SHAFT

HEX
NUT

STUD

PACKING
FOLLOWER

HEX
NUT

TYPICAL PTFE
V‐RING
PACKING

A7090 / IL

SHAFT

STUD

HEX NUT

PACKING
FOLLOWER

V‐RING PACKING

OUT'BD BEARING

PACKING

RING

ANTI‐BLOWOUT

SHAFT

SHOULDER

3‐ THROUGH 12‐INCH SIZES

14‐ THROUGH 24‐INCH SIZES

16B5082 / DOC

Disassembly

WARNING

The edges of a rotating valve disk (key 3) have a shearing effect that might result in personal injury. To avoid personal
injury, keep clear of the disk edges when rotating the disk.

CAUTION

When removing the actuator from the valve, do not use a hammer or similar tool to drive the lever off the valve shaft.
Driving the lever or actuator off the valve shaft could damage the valve internal parts.
If necessary, use a wheel puller to remove the lever or actuator from the valve shaft. It is okay to tap the wheel puller screw
lightly to loosen the lever or actuator, but hitting the screw with excessive force could also damage internal valve parts.
Never use a wrench or pliers on the drive shaft. A damaged shaft could cut the packing and allow leakage.

Unless otherwise indicated, key numbers and part names are listed in figures 7 and 8.

1. Remove the actuator and valve, as an assembly, from the pipeline, and then remove the actuator from the valve.

Note

It is not necessary to remove the retaining ring and seal ring when removing the shaft(s) and disk.

«
...
14
15
16
17
18
...
»

Содержание Fisher POSI-SEAL A31A





























Отзывы:

Нет отзывов

Похожие инструкции для Fisher POSI-SEAL A31A

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Jabra Страницы: 8

Бренд: Nedap Страницы: 20

Бренд: Oceanic Страницы: 11

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

disklavier DKC-850

Бренд: Yamaha Страницы: 2

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

Бренд: Yolink Страницы: 23

Бренд: Contemporary Research Страницы: 22

Бренд: UniPOS Страницы: 6

Markoprint iJET

Бренд: Weber Страницы: 127

Easyflow J7 DN15

Бренд: Neles Страницы: 12

Бренд: QUANT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды