Emerson Fisher 4210 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

background image

4200 Series Transmitters

Instruction Manual

Form 5596
November 2006

25

Figure 11. Transmitter Printed Wiring Board

Table 9. Jumper Configuration

TYPE

CIRCUIT

PWB ASSEMBLY

JUMPERS INSTALLED

4211/4221

Transmitter Only

GE15866X012

W4, W5 (C1 Removed)

4210/4220

Transmitter with Alarms

GE15866X022

W1, W2, W4, W5, W6

4212/4222

Alarm Switches Only

GE15866X032

W3, W6

4215

Transmitter w/Alarms

−

Dual Pot

GE15866X042

W3, W4, W5, W6

* See figure 5 for jumper locations on the printed wiring board.
NOTES:
1. The three wire cable assembly connected to J3 provides the position switch circuit output to relays K1 and K2 on the field circuit printed wiring board.
2. Terminal block number 1 (TB1) provides the connections for the three wire cable assembly from the potentiometer. On a dual potentiometer system, it provides the transmitter input
only.
3. Connector J2 is only used with a dual potentiometer or for position switches without transmitter circuit. It provides the position switch circuit input to the printed wiring board.
4. The two wire cable assembly connected to J1 is used for the transmitter output signal, (4 to 20 milliamperes), and is connected to the RFI filter.

Replacement:

Note

When replacing connectors J1, J2, and
J3 do not reverse the connector. The
connector can be forced on in the
opposite direction. Reversing any
connector can cause incorrect
operation of the transmitter. Refer to
figure 8, view A, for proper insertion of
the connectors.

1. Check the printed wiring board for correct jumper
configuration. Refer to table 9.

2. When the replacement board is ready, lower the
board into the transmitter compartment.

3. Insert and tighten the three screws.

4. Install the plug connections that were removed.

5. Connect the red and black wires to the printed
wiring board according to the transmitter type.

6. Perform the potentiometer alignment and
calibration procedures.

«
...
23
24
25
26
27
...
»

Содержание Fisher 4210













































Отзывы:

Нет отзывов

Похожие инструкции для Fisher 4210

Бренд: MAMAC SYSTEMS Страницы: 2

Бренд: Park Air Страницы: 73

Бренд: S&C Страницы: 62

Бренд: Yaesu Страницы: 35

Бренд: Maas Страницы: 72

Smart Tag ST008

Бренд: SportIQ Страницы: 3

Бренд: Dolphin Страницы: 17

PRYMEBLUPUSH-TO-TALK

Бренд: PRYME Radio Product Страницы: 2

Бренд: M-system Страницы: 2

Бренд: Icom Страницы: 10

Бренд: PS Engineering Страницы: 40

Бренд: F.u.n.k.e. Страницы: 81

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 7

Бренд: Clas Ohlson Страницы: 4

Бренд: JVC Страницы: 2

Kenwood TK-5220

Бренд: JVC Страницы: 128

Бренд: Intek Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды