background image

Electric Shock Hazard: 

Using an ungrounded or improperly connected 

appliance can result in serious injury or death from electrical shock.

Property Damage: 

To avoid water damage, replace any loose or split tubing. 

Periodically inspect the unit for any signs of leakage and immediately remove from ser-
vice any unit suspected of leaking.

Personal Injury: 

This tank is a non-pressurized tank. DO NOT modify this system.  

DO NOT close vent tube or connect other type dispensers or valves to the tank. Use 
only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an 
authorized InSinkErator Service agent for repairs or replacement components.

This appliance must be grounded. 

This instant hot water dispenser is equipped with a cord that has a 

grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly 
installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided  
with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check 
with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is 
properly grounded.

Fire Hazard: 

To minimize possibility of fire, DO NOT store flammable items such as 

rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other  
flammable vapors and liquids in the vicinity of this or any other appliance.

An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. 
To avoid possible property damage and personal injury, this instant hot water dispenser should 
be regularly examined for leakage and/or corrosion and replaced when necessary. A drain pan, 
plumbed to an appropriate drain or outfitted with a leak detector, should be used in those 
applications where any leakage could cause property damage. To check for corrosion,  
examine the appearance of the dispensed water in a clear glass once every three (3) months. 
If there is any discoloration or rusty appearance, unplug  and drain unit as described in the 
Seasonal Storage/Drainage section on page 14 of this manual. If the water discoloration 
remains after draining and refilling unit, discontinue use and contact an authorized InSinkErator 
service agent.

12

This warranty is provided by InSinkErator, a division of Emerson Electric Co., (“

InSinkErator

” or “

Manufacturer

” or “

we

” or “

our

” or 

us

”) to the original consumer owner of the InSinkErator product with which this warranty is provided (the “

InSinkErator Product

”), 

and any subsequent owner of the residence in which the Product was originally installed (“

Customer

” or “

you

” or “

your

”). 

InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject 
to the exclusions described below, for the “

Warranty Period

”, commencing on the later of: (a) the date your InSinkErator Product is 

originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial number. 
You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation supporting 
either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute discretion, 
based upon your InSinkErator Product serial number.

What is Covered

This warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used by a consumer 
Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE REMEDY 
UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE INSINKERATOR PRODUCT.

What is not Covered

This limited warranty does not extend to and expressly excludes:

 

•  Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s  

 

 

control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s),  

 

 

failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or  

 

 

local electrical and plumbing codes.

 

•  Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents  

 

 

or comparable and reasonably expected losses or damages. 

In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or  
industrial application.

No Other Express Warranty Applies

This warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written or 
verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on 
behalf of Manufacturer. The terms of this warranty shall not be modified by the Manufacturer, the original owner, or their respective 
successors or assigns.

What we will do to Correct Problems

If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions  
concerning your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator AnswerLine 
at 1 (800) 558-5700, or visit our website at www.insinkerator.com. You may also notify us at: InSinkErator Service Center, 4700 21st 
Street, Racine, Wisconsin 53406 USA.

The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator 
Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your  
installation receipt, or (b) the date shown on your purchase receipt.

Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator Product 
is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service Center. 
Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only an  
authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty claims  
arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service representative.

If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either repair 
or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair or 
installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined by 
Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be provided to 
you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired, the warranty on 
the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty Period.

Limitation of Liability

TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE 
REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING 
ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE 
INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. 
MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, 
REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, 
NEGLIGENCE, STRICT LIABILITY, OTHER SORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU EXCEED THE 
PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT. 

The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or 
revenue, cost of capital or loss or damage to property or equipment.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to 
you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

IN-HOME FULL SERVICE LIMITED WARRANTY

13

Dispenser:  

5-year warranty

Stainless Steel Tank: 

3-year warranty

Filtration System: 

1-year warranty 

(excluding replaceable filtration cartridge)

Содержание F-GN1100


























Отзывы: