Emerson Copeland OLE-49 Скачать руководство пользователя

Страница: 23 / 58

AGL_Unit_LOCU_EN_Rev00

2.11.4 Double commands

– Entering programming level 1 "Pr1"

Press simultaneously for about 3 seconds to lock (

PoF

) or unlock (

Pon

) the

keyboard.

Press simultaneously to leave the programming mode or menu. On submenus

rtC

and

EEV

this combination allows to go back to the previous level.

Press simultaneously for about 3 seconds to access the first level of
programming mode.

Table 14: Double commands

The device provides 2 programming levels:

▪

Pr1

with direct access

▪

Pr2

protected with a password (intended for experts)

2.11.5 How to program the parameters (Pr1 and Pr2)

Access pre-

program level

Press simultaneously for about 3 seconds to access the pre-
programming level. The message

rtC

(real time clock) appears.

Access

program level

Press simultaneously for about 3 seconds to access the
programming level. The message

Par

appears.

Access Pr1

Press the

SET

button to enter program level Pr1. First parameter

C01

C07

appears.

Select item

Select the parameter or submenu using the arrows.

Show value

Press the

SET

button.

Modify

Use the arrows to modify the value.

Conf irm and

store

Press the

SET

button: the value will blink for 3 seconds, then the

display will show the next parameter.

EXIT

Press simultaneously to exit the programming mode or wait
f or 30 seconds (MTO) without pressing any key.

Table 15: Programming level 1 parameters

When entering the programming level for the first time the display will show the

rtC

(real time clock)

label.

▪

Press

to access parameters N01/02/03/04/05 to adjust time & date. For further details, see

section 2.13 "Parameters level 1

– Required settings"

▪

Press

to change from the

rtC

label to the

Par

label, in order to access the programming

level 1.

▪

Press

: the parameters of programming level 1 can be changed.

2.11.6 Entering programming level 2 "Pr2"

To enter the Pr2 programming menu:

▪

Press

simultaneously for 3 seconds. The f irst parameter label will be displayed.

▪

Press

till the

T18

label is displayed, then press the

key.

▪

The blinking

PaS

label will be displayed; wait for a few seconds.

▪

The display will show "

0 - -

" with blinking 0: insert the password [

321

] using the

and

keys

and confirming with the

key.

Содержание Copeland OLE-49



























































Результаты поиска

Содержание Copeland OLE-49

Отзывы:

Похожие инструкции для Copeland OLE-49

Бренды по названию

Популярные бренды

Emerson Copeland OLE-49, Инструкции по применению

Результаты поиска

Содержание Copeland OLE-49

Отзывы:

Похожие инструкции для Copeland OLE-49

Бренды по названию

Популярные бренды