Emerson COM Express Carrier Скачать руководство пользователя страница 95

Страница: 95 / 103

COM Express Carrier Type 2

Page 95 of 103

Design Guide



Do not route traces under crystals, crystal oscillators, clock synthesizers, magnetic devices or ICs

that use, and/or generate, clocks.



Stubs on differential signals should be avoided due to the fact that stubs will cause signal reflections

and affect signal quality.



Keep the length of high-speed clock and periodic signal traces that run parallel to high-speed signal

lines at a minimum to avoid crosstalk. Based on EMI testing experience, the minimum suggested
spacing to clock signals is 50mil.



Use a minimum of 20mil spacing between the differential signal pairs and other signal traces for

optimal signal quality. This helps to prevent crosstalk.



Route all traces over continuous planes (VCC or GND) with no interruptions. Avoid crossing over

anti-etch if at all possible. Crossing over anti-etch (split planes) increases inductance and radiation
levels by forcing a greater loop area.

Figure 41 Layout Considerations

In order to determine the necessary trace width, trace height and spacing needed to fulfill the

requirements of the interface specification, it's necessary to use an impedance calculator.

Содержание COM Express Carrier








































































































Результаты поиска

Содержание COM Express Carrier

Отзывы:

Похожие инструкции для COM Express Carrier

Бренды по названию

Популярные бренды

Emerson COM Express Carrier, Руководство по конструкции

Результаты поиска

Содержание COM Express Carrier

Отзывы:

Похожие инструкции для COM Express Carrier

Бренды по названию

Популярные бренды