manualshive.com logo in svg

Emerson Bettis Multiport, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Emerson Bettis Multiport Скачать руководство пользователя страница 23

Installation, Operation and Maintenance Manual

 

MAN-02-10-93-0700-EN  Rev. 0

 

 

May 2019

19

Section 6: Field Setup Using MPA Config Software

Field Setup Using MPA Config Software

6.8 

Control Screen

The control screen (see Figure 14) is a valuable tool for commissioning the system.  
All functions of the system may be tested prior to commissioning with the DCS. This screen 
may be used to troubleshoot   any   problems   should they  occur.  Field  diagnostic  
messages are displayed in the “Field Diagnostics  Information”  box.  All active alarms may 
be viewed at a glance in the “Alarms” section of the Control Screen.

Figure 14 

1. 

“Mode”  displays  the  mode  selected by the selector switch of the LDM or 
combined  logic  of  both  LDM  and RDM selector switches.

2. 

“Status” displays Running or Stop state of the actuator.

3. 

“At Port” displays the port number position of the actuator and whether the MPA 
is at the port within 1 degree or within 2 degrees.

4. 

“Torque” is displayed as percentage of the full torque rating of the actuator. Torque 
is displayed from 10% to 99% in 1% increments. Torque less than 10% is displayed 
as zero because torque between 0% and 10% cannot be accurately measured.

5. 

“Encoder Value” is the 12-bit raw data from the position encoder in the range of 
0 to 4095. This value is also displayed on the Factory Setup screen so it can be 
compared to port calibration value of each port.

6. 

“Valve Control” allows commanding the actuator to go to the next port or go to a 

desired port number. “Go to Port” is the new setpoint in the range of 0 to 7. “Current 

Setpoint” is the last commanded value stored in the actuator. Each time the actuator 
is powered up or  it  torques  out  while  moving,  it  loads  an  invalid  setpoint  of 
255  to the  “Current Setpoint”. This prevents the actuator from moving until a valid 

setpoint from 0 to 7 is entered in the “Go to Port” and sent to the actuator. If “Next 

Port” button is clicked while 255 is in the “Current Setpoint”, then the next higher 
port number from the current position will be loaded to the current setpoint.

Содержание Bettis Multiport










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды