Emerson AMS Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 92

Emerson AMS Скачать руководство пользователя страница 42

later release. With full support for communication between AMS Asset Monitors ensure
that each AMS Asset Monitor has a unique Address Plug installed.

The third RJ-45 Ethernet socket with a speed of 1 Gbit/s is to connect to a WAN

configuration and to connect to subsequent systems such as Plantweb Optics. See

for the location of the RJ-45 sockets.

To keep the IP protection class of the AMS Asset Monitor, Emerson recommends not to
use prefabricated Ethernet cables with RJ-45 plugs. Instead, use Ethernet cables without
plugs and RJ-45 plugs that can be crimped onto an Ethernet cable.

Prerequisites

•

RJ 45 plugs that can be crimped onto an Ethernet cable.

•

Crimping tool for RJ 45 plugs, if required for the selected plugs.

•

Cable tester

•

CAT 5(e) or higher Ethernet cable

•

Maximum Ethernet cable length between devices is 100 meters.

•

Installation in accordance to Ethernet standards.

All Ethernet cables used to connect the AMS Asset Monitor must be made, installed, and
tested by an experienced LAN installer.

Follow the steps to connect an Ethernet cable:

Procedure

1. Lead the Ethernet cable through a suitable cable gland at the bottom of the AMS

Asset Monitor.

2. Strip the Ethernet cable in accordance to the needs of the RJ 45 plug.
3. Crimp the RJ 45 plug on the Ethernet cable.
4. Plug the RJ 45 plug into the needed Ethernet connector.

4.11.1

Permissible network topology

There are three different permissible network topologies available to connect up to eight
AMS Asset Monitors:

Daisy-chained network

Devices connected in series.

Star network

Devices connected to a central switch.

Hybrid network

A mix of the daisy-chained network and the star network

Note

With full support for communication between AMS Asset Monitors ensure that each AMS
Asset Monitor has a unique Address Plug installed. Two or more Address Plugs with the
same number within a network cause communication failure.

4

W

ide

A

rea

N

etwork

Installing AMS Asset Monitor hardware

Installation Guide

April 2020

MHM-97923-PBF

42

MHM-97923-PBF, Rev. 1.0

«
...
40
41
42
43
44
...
»

Содержание AMS





























































































Отзывы:

Нет отзывов