Emerson AMS Скачать руководство пользователя страница 45

Страница: 45 / 92

Figure 4-18: Network topology – hybrid

A. First RJ 45 socket of the Ethernet switch (ACN/LAN)

B. Second RJ 45 socket of the Ethernet switch (ACN/LAN)

C. RJ 45 socket for connection to WAN for configuration of the AMS Asset Monitor and

connection to subsequent systems such as Plantweb Optics

D. Optional connection, if no connection between switch and ACN

E. Connection to an Area Controlled Network (ACN)
F. Switch

Connect AMS Asset Monitor in a daisy-chained network

Figure 4-19: RJ-45 sockets

A. RJ-45 sockets of the 100 Mbit/s Ethernet switch

Procedure

1. Connect the Area Controlled Network (ACN) to one RJ-45 socket of the 100 Mbit/s

switch of the first AMS Asset Monitor.

Installation Guide

Installing AMS Asset Monitor hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

Содержание AMS





























































































Результаты поиска

Содержание AMS

Отзывы:

Похожие инструкции для AMS

Бренды по названию

Популярные бренды

Emerson AMS, Руководство по установке

Результаты поиска

Содержание AMS

Отзывы:

Похожие инструкции для AMS

Бренды по названию

Популярные бренды