Emerson AMS Скачать руководство пользователя страница 36

Страница: 36 / 92

Figure 4-12: Universal mounting bracket – horizontal mounting

A. M8 x 1.25 hex nut (4x) for fastening the clamping jaws

B. Clamping jaw (2x)

C. Mounting plate

D. M8 split lock washer (12x)

E. M8 x 1.25 x 120 mm hex head bolt for fastening the clamping jaws
F. M8 x 1.25 x 18 mm hex head bolt (4x) for mounting the plate on the back of the AMS

Asset Monitor

Note

Ensure that the post can permanently bear the weight of the AMS Asset Monitor.
Do not mount the AMS Asset Monitor on piping in use.

Prerequisites

You need two suitable spanners/wrenches with 13 mm opening. The tightening torque
may vary depending on the on-site situation.

Procedure

1. Insert the M8 x 1.25 x 120 mm hex head bolts including the split lock washers in the

mounting plate.

•

For mounting on a vertical post, use the holes in the middle of the bracket (see

Figure 4-11

Installing AMS Asset Monitor hardware

Installation Guide

April 2020

MHM-97923-PBF

MHM-97923-PBF, Rev. 1.0

Содержание AMS





























































































Результаты поиска

Содержание AMS

Отзывы:

Emerson AMS, Руководство по установке, Страница: 36 / 92

Результаты поиска

Содержание AMS

Отзывы: