manualshive.com logo in svg

Emerson AMS, Руководство по установке, Страница: 27 / 92

Поделиться
Скачать
Emerson AMS Скачать руководство пользователя страница 27

Figure 4-3: Overview – open AMS Asset Monitor

A. Ethernet switch with two RJ-45 connectors (ACN

2

/DCN

3

) to daisy chain up to eight AMS

Asset Monitors and to connect to an ACN, speed 100 Mbit/s

B. RJ-45 Ethernet connector for configuration and connection to subsequent systems,

speed 1 Gbit/s

C. Status light

D. CHARM baseplate with 12 slots for up to 12 CHARM terminal blocks, 12 CHARMS, and a

CHARM labeling component

E. Mounting holes
F. Door hinge

G. Screws holes for securing the door
H. Power module slot

I. Address plug slot
J. External grounding terminal

K. Power supply terminals

L. Covered. Non-functional. For internal use only.

M. microSD Card slot (for future use)

N. Reset button with status LED

O. Internal grounding terminals

+24 V DC Power Module

The +24 V DC Power Module is used to supply the AMS Asset Monitor including all installed
CHARMs.

2

A

rea 

C

ontrolled 

N

etwork

3

D

aisy 

C

hained 

N

etwork

Installation Guide 

Installing AMS Asset Monitor hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

27

Содержание AMS





























































































Отзывы:

Нет отзывов