Emerson 0478-0047-03 Скачать руководство пользователя | Manualshive

Страница: 34 / 40

background image

How to use this

Diagnostics

34

SI-I/O User Guide

Issue Number: 3

9 Diagnostics

9.1

Overview

This section provides basic diagnostic information intended to resolve the most common problems encountered when setting up an SI-I/O option
module.

Drive trip display codes

If the option module detects an error during operation, it will force a trip on the drive. However, the trip string displayed on the drive will only indicate
which slot initiated the trip. The exact reason for the trip will be indicated in the drive trip code parameters (Pr

10.020

and Pr

10.070

).

Table 9.1 shows the possible trips that will be displayed on the drive when a problem is detected with the option module or when the option module
initiates a trip.

Table 9.1 Digital I/O - 1-4

9.1.1

Module error codes

If the option module detects an internal error during operation, it will force a trip on the drive and provide a sub-trip string for a clearer definition of the
trip. Table 9.2 shows the possible module error codes.

Table 9.2 Module error codes

Trip

Description

SlotX HF

The drive has detected that an option module is present but is unable to communicate with it due to a hardware fault.

SlotX Error

User trip generated by the option module

SlotX Not
Fitted

This trip will occur if a drive slot was previously configured with an option module but on power up, no option module was detected.

SlotX
Different

This trip will occur if a drive slot was previously configured with an option module but on power up, a different option module was
detected. Replacing the option module with another one of the same ID number will not initiate this trip.
The trip will also occur if an option module is installed to a previously unused slot.

Value

Text

Description

200

SW fault

Software fault

201

BG Orun

Background task overrun

202

FW invalid

Invalid firmware for hardware
version

203

Drv unknown

Unknown drive type

204

Drv unsupported

Unsupported drive type

205

Mode unknown

Unknown mode

206

Mode unsupported

Unsupported mode

207

FLASH corrupt

Corrupted Non-volatile Flash

208

Dbase init

Database initialization error

209

FS init

File system initialization error

210

Memory alloc

Memory allocation error

211

Filesystem

File system error

212

Configuration

Configuration file error

213

OHt

Overheated

214

TO drv

The drive has not responded
with the watchdog period

215

eCMP

eCMP comms failure

216

TO eCMP slot 1

Slot 1 eCMP timeout

217

TO eCMP slot 2

Slot 2 eCMP timeout

218

TO eCMP slot 3

Slot 3 eCMP timeout

219

TO eCMP slot 4

Slot 4 eCMP timeout

220

Output overload

Digital output overload

«
...
32
33
34
35
36
...
»

Содержание 0478-0047-03









































Отзывы:

Нет отзывов

Похожие инструкции для 0478-0047-03

Бренд: Jafar Страницы: 10

Бренд: Jabra Страницы: 8

Бренд: cinetto Страницы: 56

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: Greenheck Страницы: 4

Бренд: NXP Semiconductors Страницы: 39

Бренд: SAGEMCOM Страницы: 2

Бренд: Instant Care Страницы: 2

Soluna Remote Control

Бренд: Rollei Страницы: 8

Бренд: TSM Страницы: 2

Бренд: IMG STAGELINE Страницы: 14

Бренд: VAT Страницы: 77

Бренд: M-system Страницы: 7

Бренд: Texecom Страницы: 21

Бренд: Rare Waves Страницы: 18

Бренд: SAFERA Страницы: 32

Бренд: Mircom Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды