Emerson 0478-0047-03 Скачать руководство пользователя

Страница: 36 / 40

SI-I/O User Guide

Issue Number: 3

10 Technical Data

10.1

Digital inputs/outputs (Terminals 2-5)

10.2

Digital Inputs (Terminals 7-9)

10.3 Differential Analog Input (Terminals 7 and 8)

(Unidrive M600 - M800 only)

Default function

Positive logic mode

Type

Positive or negative logic inputs or Negative logic push-pull or open collector outputs

Absolute maximum voltage range -18 V to +36 V
Update time

2 ms for Unidrive M600 - M800
8 ms for Unidrive M200 - M400

Operating as an input

Logic mode controlled by

S.01.008

Voltage range

0 V to +24 V

Impedance

>2 mA @ +15 Vdc from IEC61131-2, clause 3.3.1 type 1

Input thresholds

10 V ±0.8 V

Operating as an output

Mode controlled by

S.01.009

Current limits

100 mA for Digital I/O 1&2
100 mA for Digital I/O 3&4

Isolation

Not isolated from control circuit

Overvoltage protection

Series resistor, filter capacitor and clamping diodes

Default function

Positive logic mode

Type

Positive or negative logic inputs

Absolute maximum voltage range -18 V to +36 V
Update time

2 ms for Unidrive M600 - M800
8 ms for Unidrive M200 - M400

Operating as an input

Logic mode controlled by

S.01.008

Voltage range

0 V to +24 V

Impedance

>2 mA @ +15 V dc from IEC61131-2, clause 3.3.1 type 1

Input thresholds

10 V ± 0.8 V

Type

Bipolar differential analog input

Full scale voltage range

±10 V ± 1 %

Absolute maximum voltage range -18 V to +36 V
Differential Input resistance

>100k

Ω

Resolution

16 bit

Maximum offset

50 mV

Maximum nonlinearity

0.3 % of input

Input filter bandwidth single pole

≈

1 kHz

Sample period

2 ms

Over voltage protection

Not isolated from control circuit

Содержание 0478-0047-03









































Результаты поиска

Содержание 0478-0047-03

Отзывы:

Похожие инструкции для 0478-0047-03

Бренды по названию

Популярные бренды

Emerson 0478-0047-03, Руководство пользователя

Результаты поиска

Содержание 0478-0047-03

Отзывы:

Похожие инструкции для 0478-0047-03

Бренды по названию

Популярные бренды