Emerson 0478-0047-03 Скачать руководство пользователя

Страница: 11 / 40

SI-I/O User Guide

Issue Number: 3

6 Single line descriptions

6.1

Single line descriptions

6.1.1

Menu 0 - Setup

6.1.2

Menu 1 - I/O Setup

Parameter

Range (

)

Default (

)

Type

MM.001

Module ID

0 to 999

209

Num ND NC PT

MM.002

Software Version

00.00.00.00 to 99.99.99.99

Num ND NC PT

MM.003

Hardware Version

00.00 to 99.99

Num ND NC PT

MM.004

Serial Number LS

0 to 99999999

Num ND NC PT

MM.005

Serial Number MS

0 to 99999999

Num ND NC PT

MM.006

Module status

Initializing (0), OK (1), Config (2), Error (3)

Num ND NC PT

MM.007

Module reset

Off (0) or On (1)

Off (0)

Bit

MM.008

Module default

Off (0) or On (1)

Off (0)

Bit

MM.030

Slot Indicator

0 to 8

Num ND NC PT

MM.031

Slot Menu Number

0 to 255

Num ND NC PT

Parameter

Range (

)

Default (

)

Type

S.01.001

Reset I/O Interface

Off (0) or On (1)

Off (0)

Bit

S.01.002

Default I/O Interface

Off (0) or On (1)

Off (0)

Bit

S.01.004

Option Module Status

Initializing (0), OK (1), Config (2), Error (3)

Txt

NC PT

S.01.005

I/O Output Enable
Register

0000000000 to 1111111111

0000000000

Bin

S.01.006

I/O Input Register

00000000 to 11111111

Bin

S.01.007

I/O Output Register

0000000000 to 1111111111

0000000000

Bin

S.01.008

Digital I/O Logic Polarity

Negative Logic (0) or Positive Logic (1)

Positive Logic (1)

Txt

S.01.009

Open Collector Output

Push-Pull (0) or Open Collector (1)

Push-Pull (0)

Txt

S.01.010

I/O Read Word

0000000000 to 1111111111

0000000000

Bin

S.01.011

T2 Digital I/O 1 Mode

Digital Input (0) or Digital Output (1)

Digital Input (0)

Txt

S.01.012

T3 Digital I/O 2 Mode

Digital Input (0) or Digital Output (1)

Digital Input (0)

Txt

S.01.013

T4 Digital I/O 3 Mode

Digital Input (0) or Digital Output (1)

Digital Input (0)

Txt

S.01.014

T5 Digital I/O 4 Mode

Digital Input (0) or Digital Output (1)

Digital Input (0)

Txt

S.01.015

T7 Digital Input 5 /
Analog Input 1 Mode

Digital Input (0) or Volt IN (1)

Volt IN (1)

Txt

S.01.016

T8 Digital Input 6 /
Analog Input 2 Mode

Digital Input (0) or Volt IN (1)

Volt IN (1)

Txt

S.01.017

T9 Digital Input 7 /
Analog Input 3 Mode

Digital Input (0), Volt IN (1), 4-20mA Low (2), 20-

4mA Low (3), 4-20mA Hold (4), 20-4mA Hold (5),

0-20mA (6), 20-0mA (7), 4-20mA Trip (8), 20-

4mA Trip (9), 4-20mA (10), 4-20mA (11)

Volt IN (1)

Txt

S.01.018

T11 Digital Input 8 /
Analog Output 1 Mode

Digital Input (0), Volt Out (1), 4-20mA (2), 20-

4mA (3), 0-20mA (4), 20-0mA (5),

Volt Out (1)

Txt

Содержание 0478-0047-03









































Результаты поиска

Содержание 0478-0047-03

Отзывы:

Похожие инструкции для 0478-0047-03

Бренды по названию

Популярные бренды

Emerson 0478-0047-03, Руководство пользователя

Результаты поиска

Содержание 0478-0047-03

Отзывы:

Похожие инструкции для 0478-0047-03

Бренды по названию

Популярные бренды