manualshive.com logo in svg

EMC Qlogic QLA22 Series, Руководство пользователя

Поделиться
Скачать
EMC Qlogic QLA22 Series Скачать руководство пользователя страница 31

2

Upgrading to Windows 2003 from Windows 2000 or Windows NT 4.0

2-19

Installing and Configuring the HBA Driver

Upgrading to Windows 2003 from Windows 2000 or 
Windows NT 4.0

Note the following if upgrading to Windows 2003:

◆

Upgrading from Windows NT 4.0 — The Windows NT4 drivers 
will not be preserved while upgrading to Windows 2003. You 
should obtain the correct Windows 2003 drivers (refer to 

Downloading QLogic Drivers and Firmware

 on page 2-2) and 

reinstall the drivers after the upgrade is complete.

◆

Upgrading from Windows 2000 — The Windows 2000 drivers 
may be preserved while upgrading to Windows 2003. These 
SCSIPort drivers (including the native Windows 2003 SCSIPort 
drivers) are not supported by EMC for Windows 2003. You 
should obtain the correct Windows 2003 drivers (refer to 

Downloading QLogic Drivers and Firmware

 on page 2-2) and 

reinstall the drivers after the upgrade is complete.

You may wish to disconnect your storage during the Windows upgrade, and 
reconnect it after the approved Windows 2003 drivers have been installed.

Содержание Qlogic QLA22 Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды