manualshive.com logo in svg

EMC Qlogic QLA22 Series, Руководство пользователя

Поделиться
Скачать
EMC Qlogic QLA22 Series Скачать руководство пользователя страница 3

EMC Fibre Channel with QLogic HBAs in Windows Hosts

iii

Preface

...........................................................................................................................  vii

Chapter 1

Introduction

Understanding Persistent Binding in a Fabric Environment .... 1-2

Chapter 2

Installing and Configuring the HBA Driver

Introduction ...................................................................................... 2-2

Downloading QLogic Drivers and Firmware ...................... 2-2
Verifying and Downloading the Documentation ................ 2-2

Installing an HBA ............................................................................ 2-3

Special Installation Sequence for Stratus ftServers and 
EMC CLARiiON Arrays .......................................................... 2-4
Special Instructions for CLARiiON CX200-Series 
Direct-Connect Dual-Host Clustering Configurations ....... 2-4

EMC HBA Settings .......................................................................... 2-8

Pre-Configured Settings........................................................... 2-8
Configuring NVRAM for Stratus ftServers .......................... 2-9
Fibre-Down Servers with Embedded QLogic HBAs......... 2-10
Updating Firmware/BIOS and Applying NVRAM 
Settings ..................................................................................... 2-10
Manually Setting the HBA Data Rate .................................. 2-12
Setting the Topology for QLA22xx/23xx and Windows .. 2-13

Installing the HBA Driver............................................................. 2-14

Driver Revision History......................................................... 2-14
Where to Find the Driver....................................................... 2-14
Windows 2003 STORPort Updates....................................... 2-14
Installation Procedure for Windows NT Hosts .................. 2-15

Contents

Содержание Qlogic QLA22 Series















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды