EMC Avamar Data Store Gen4T Скачать руководство пользователя

Страница: 30 / 32

Figure 14 Power Supply Installation

2. Insert the replacement power supply into the SP module and push until it clicks into

place.

3. Connect the AC power cord to the replacement power supply and fasten the retaining

clip to secure the cord.

4. Allow several seconds for the node to recognize the power supply and determine

whether it is working properly. The

AC Good

and

DC Good

LEDs should illuminate

green. The

Attention

LED should stay off.

Verifying the replacement power supply

Procedure

1. Type the following command:

avsysreport power-supply

Output similar to the following is displayed:

=== Power supply redundancy

Status : Ok

Redundancy State : Fully Redundant

=== Power supplies

Power Supply ID : 0

Status : Ok

Location : PSA

Operational State : Inserted, Power Good

Firmware Revision : 4.20.0.1

Serial Number : FPSAG144900460

Power Supply ID : 1

Status : Ok

Replacing a Power Supply

EMC Avamar Data Store Gen4T

Customer Service Guide

Содержание Avamar Data Store Gen4T

































Результаты поиска

Содержание Avamar Data Store Gen4T

Отзывы:

Похожие инструкции для Avamar Data Store Gen4T

Бренды по названию

Популярные бренды

EMC Avamar Data Store Gen4T, Руководство по обслуживанию клиентов

Результаты поиска

Содержание Avamar Data Store Gen4T

Отзывы:

Похожие инструкции для Avamar Data Store Gen4T

Бренды по названию

Популярные бренды