background image

3

 

CAUTION! 

A CAREFUL OPERATOR IS THE BEST OPERATOR 

 

Most accidents can be prevented by  becoming familiar with all 

controls before operating the backhoe, keeping in mind the safety 

precautions stated below, and working safely. 

 

• 

Read Operator’s Manual before operation. 

 

• 

Enter and exit operator’s platform from between stabilizers and tires 

only.

 

 

• 

Operate backhoe from operator’s seat only and be sure the seat is 

firmly locked into position.  Always keep your feet on the foot rest 

area.

 

 

• 

Backhoe digging forces can lift and turn tractor over.  For maximum 

stability, set stabilizers to remove weight from rear tractor tires with-

out lifting them off the ground.  Always lower both stabilizers to 

avoid risk of overturning.  Sufficient counterweight or a front end 

loader might be required in some applications to improve stability.  

See your dealer for more information.  

 

 

• 

Check all hoses and fittings for damage or leaks before operating 

the backhoe. 

 

 

• 

All levers must be in the neutral position when starting your tractor.  

 

 

• 

Before operating the backhoe, look for obstructions in the line of 

movement.  Stay clear from low overhead electrical wires when the 

backhoe is in the upper position.  Verify the ground’s conditions 

before digging and ensure digging area is free from underground 

cables and pipes.  Keep people and animals at a safe distance 

while operating the backhoe and never let anyone into the bucket or 

onto the backhoe when driving tractor.  Never leave an unattended 

tractor running.  

 

 

• 

Never move tractor while operating backhoe.

 

 

• 

Do not use backhoe without front end loader attached. 

 

 

• 

To avoid handling stability problems, never exceed the maximum 

capacity of your backhoe.

 

 

• 

Never use your backhoe as a battering ram (swinging left to right) 

to push earth.  This could affect the good working condition of your 

backhoe.  

 

 

• 

Never operate the tractor’s three point hitch if the backhoe is con-

nected to it.  

 

 

• 

Keep the valve and lever setting clear from any obstructions.  Never 

remove the safety guards on the stabilizers, cylinders, or the relief 

valve covering box.  Keep all guards in place. 

 

 

• 

Do not repair or service backhoe unless it is mounted on tractor and 

securely supported.  Loss of oil or removal of parts could cause 

backhoe to collapse.  

 

 

Содержание Wallenstein GX600

















Отзывы: