EMB Wallenstein EC2500 Скачать руководство пользователя | Manualshive

Страница: 24 / 40

background image

24

4. Starting the Generator:

a. Plug in power cords from appliances or

loads.

b. Turn all the appliances or electrical

loads off .

c.

Refer to engine manual for detailed
engine starting procedure.

d. Turn the ignition switch ON.

e. Pull out the choke if the engine is cold

or hasn't been run for awhile.

f.

Pull sharply on the starting T-bar to start
the engine.

g. Run the engine until it warms and the

choke is completely closed.

h. Turn the appliance on or plug in the

electrical load.

5. Stopping:

a. Turn the appliance off or unplug the

electrical load.

b. Run the engine for approximately three

minutes to allow the engine to cool.

c.

Turn engine off .

6. Emergency Stopping:

Turn the engine off if an emergency arises.
Correct the condition before resuming work
and re-starting the engine.

7. Terrain:

The  generator  works  well  in  a  wide  variety
of operating conditions but it should always
be positioned on the level.  When the frame
is  level,  fuel  spillage  is  minimized  and  the
gas  tank  capacity  is  maximized.    Do  not
operate unless the frame is level.

Fig. 6 STARTING/STOPPING

EC2500

EC2600

«
...
22
23
24
25
26
...
»

Содержание Wallenstein EC2500









































Отзывы:

Нет отзывов

Похожие инструкции для Wallenstein EC2500

Бренд: Caliber Страницы: 10

Бренд: Califone Страницы: 11

OLYMPUS JEFGENPET30EL

Бренд: Jefferson Страницы: 20

Бренд: Champion Страницы: 29

Бренд: iLive Страницы: 24

Бренд: Hubner Страницы: 54

Power WHISPERWATT DCA70USI2

Бренд: MULTIQUIP Страницы: 84

Бренд: Jefferson Professional Tools & Equipment Страницы: 9

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 31

Бренд: Philips Страницы: 32

Бренд: Blaupunkt Страницы: 162

Бренд: LOTRONIC Страницы: 20

Бренд: Excera Страницы: 40

Бренд: Excera Страницы: 51

Бренд: DUROMAX Страницы: 74

Бренд: DUROMAX Страницы: 76

Бренд: DUROMAX Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды