background image

20

User Manual PRIMA 2 scale

ELZAB S.A.

 – READING OF SETTINGS

Meaning

This function shows all currently chosen settings in the User Menu 

For example for the factory settings there

will be chosen the following data:

1.

1

3

5

0

1

Protocol Type:

ELZAB EXTENDED

Transmission Speed:

9600 BITS/SEC.

Transmission

Parameters:

8-EVEN-1

Parity Checking:

NO CHECKING

Stability Condition:

HIGH STABILITY

2.

1

0

0

0

3

Minimum Result:

01xe

Transmission Mode:

AFTER PRESSING

THE KEY

Transmitting the

minus:

ONLY POSITIVE

Transmitting the result

frame:

TRANSMITTING THE

RESULT FRAME

Stability waiting time:

4 SECONDS

3.

0

0

0

1

0

Data receiving lock:

LOCK OFF

Transmission key lock:

LOCK OFF

Configuration

receiving lock:

LOCK OFF

Beep:

WITH BEEP

Fixed tare:

AUTOMATIC SWIT-

CHING OFF THE

TARE

4.

1

2

0

-

-

Turning off the display

backlight: SWITCH

 OFF AFTER 15 SEC.

Power saving mode:

TURN ON AFTER 30

MIN.

Scales system:

SCALE NO. 0

Active communication

port

AUTOMATIC DETECTION

USB power source:

AUTOMATIC DETECTION

 – EXIT FROM MENU

Meaning

Exit from the User Menu to the weighing mode.

6.

 

Communication with the scale

The communication of the scale with external devices (e.g. cash register, computer) is effected via
the 

CASH REGISTER/PC

 connector (RS-232 interface). To communicate via the USB connector the

virtual serial port driver should be installed on the device cooperating with the scale. The driver
can be downloaded from www.elzab.pl.
The communication with external devices can be affected by functioning of the scale in the
situations like: unstable result, overloading and under loading of the scale, transmission mode
settings or the minimum result settings. The scale can react for those states in different ways
depending on its settings.

All the communication parameters can be changed in the “User Menu” 

. They are

permanently stored in the non volatile scale memory. The factory settings can be reset by using the

“Restore to factory settings” 

 

function. The factory settings allow the scale to cooperate

with every cash register produced by ELZAB SA factory which was approved by the Ministry of

Finance since 2001.

Содержание Prima 2

































Отзывы: