ELTEX TAU-4M.IP Скачать руководство пользователя страница 85

Страница: 85 / 126

____________________________________________________________________________________

TAU-4M.IP Subscriber gateway

DHCP-based Autoprovisioning



Parameters Priority from

- this parameter determines where you need to get the names and

location of configuration files and firmware:

–

Static settings

- the paths to the configuration files and firmware are determined

respectively from the

'Configuration File'

and

'Firmware File'

parameters; for more

algorithm details see Section 5;

–

DHCP options

- the paths to the configuration and firmware files are determined from the

DHCP options 43, 66 and 67 (to do this, select the DHCP protocol for the Internet service);
for more algorithm details see Section 5;



Provisioning Mode

- to update the firmware configuration separately, you can specify one of

several update modes:

–

Disabled

- automatic update of device configuration or firmware is disabled;

–

Periodically

- automatic update of the configuration or firmware of the device will be

performed at a specified time interval;

–

Scheduled

- the device will automatically update its configuration or firmware at a

specified time, on specified days of the week.

Содержание TAU-4M.IP































































































































Результаты поиска

Содержание TAU-4M.IP

Отзывы:

Похожие инструкции для TAU-4M.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4M.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4M.IP

Отзывы:

Похожие инструкции для TAU-4M.IP

Бренды по названию

Популярные бренды