ELTEX TAU-4.IP Скачать руководство пользователя

Страница: 116 / 190

116

VoIP Subscriber Gateways

‐

host

‐

net

‐

port.

If the

type

is not defined,

host

value is meant.

dir

– specifies the direction relative to the object. The classifier accepts the following

values:

‐

src (the object is a sender)

‐

dst (the object is a recipient)

‐

src or dst (a sender or a recipient)

‐

src and dst (a sender and a recipient).

If the

dir

is not defined,

src

dst

is meant. To enable the mode for capturing traffic

from

any

interface,

inbound

and

outbound

classifiers can be used.

proto

– specifies the protocol according to which packets are structured. The classifier

accepts the following values:

‐

ether

‐

arp

‐

decnet

‐

tcp

‐

udp.

If the primitive does not contain protocol classifiers, it is expected that all protocols

compatible with object type match the filter.

Maximum traffic dump size is 60MB. At exceeding of the threshold, new files will be
written instead of outdated ones.

3.4

The ‘Reboot’ menu

To reboot the device, click

‘Reboot’

button on the left panel of Web configurator. After that,

confirm it by clicking

‘Yes, really reboot now’

. The device rebooting may continue about one minute.

Содержание TAU-4.IP































































































































































































Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды

ELTEX TAU-4.IP, Руководство по эксплуатации

Результаты поиска

Содержание TAU-4.IP

Отзывы:

Похожие инструкции для TAU-4.IP

Бренды по названию

Популярные бренды