Elseta IOMOD HT Скачать руководство пользователя страница 10

Страница: 10 / 14

a. Driver installation

Device requires USB drivers to work as virtual com port. First-time connection between device and computer could

result in “Device driver software was not successfully installed” error.

Fig. 6.1

User then manually installs drivers by selecting downloaded driver folder:

Go to Control Panel -> Device Manager;

Select failed device;

Press “Update driver software”; following screen should appear:

Fig. 6.2

Select “x86” driver for 32bit machine, or x64 for 64bit machine. If not sure, select root folder (folder in which x64 and

x86 lays inside).

Fig. 6.3

b. IOMOD HT configuration with PuTTY terminal

Configuration of IOMOD device is done through CLI (Command Line Interface) on virtual COM port. Drivers needed for

MS Windows to install VCOM will be provided. To open up CLI simply connect to specific V-COM port with terminal

software (advised to use PuTTY terminal software. If other software is being used, user might need to send <return>

symbol after each command). When connected user should immediately see main screen:

Configuration over USB

Содержание IOMOD HT














