ELNA Elinita EF72 Скачать руководство пользователя

Страница: 46 / 46

* Regarded as good when all the results are correct.

* In case of defect, check again after adjustment or replacement of parts.

Results

8. Thread tension release motor

9. Driving motor/bobbin winding motor.

7. Thread cutter motor

Correct condition
Turn the handwheel to move the

needle bar to the zigzag phase (up

position). When pressing the needle

up/down key, the thread cutter motor

is initialized and the buzzer sounds.

Press the start/stop key to proceed

to the next step.

Faulty condition
The thread cutter motor is not

initialized.

“E4” is indicated.

The caution buzzer sounds when

the thread cutting motor starts

running.

To adjust or replace a part:
Adjust the position of the

sensor.

Replace the thread cutting motor.

Change the printed circuit board A.

Correct condition
When pressing the needle up/

down key, the motor starts running,

increasing speed evenly. The motor

stops at the needle up position.

The screen shows “OK”.

When pressing bobbin winding key

( ), the bobbin winding motor

runs.

8. Turn the power switch off to finish.

Faulty condition
The motor does not run.

The screen shows “NG”.

The bobbin winder motor does not

run.

The motor does not run smoothly.

To adjust or replace a part:
Replace the driving motor.

Replace the bobbin winder motor

Change the printed circuit board A.

Correct condition
When pressing the needle up/down

key, the thread tension release

motor is initialized and the buzzer

sounds.

Press the start/stop key to proceed

to the next step.

Faulty condition
The thread tension release motor is

not initialized.

“E3” is indicated.

The caution buzzer sounds when

the thread tension release motor

starts running.
To adjust or replace a part:
Adjust the position of the

sensor.

Replace the thread tension release

motor.

Change the printed circuit board A.

Содержание Elinita EF72















































Результаты поиска

Содержание Elinita EF72

Отзывы:

Похожие инструкции для Elinita EF72

Бренды по названию

Популярные бренды

ELNA Elinita EF72, Руководство по обслуживанию

Результаты поиска

Содержание Elinita EF72

Отзывы:

Похожие инструкции для Elinita EF72

Бренды по названию

Популярные бренды