ELNA Elinita EF72 Скачать руководство пользователя страница 41

Страница: 41 / 46

When the feed dog does not return to “Up” position and the machine do not feed a fabric,

check and adjust the feed lifting cam.

Feed dog troubleshooting

Projection of feed lifting cam

1. Check the drop feed lever

1) Remove the base.
2) Bring the needle bar at the lowest position.

(The projection of the feed lifting cam is visible at

this position.)

3) When the drop feed lever is moved left and right,

the feed lifting cam should move accordingly.

2. Check the position of the setscrew on the lower

shaft ring

Check if the setscrew A on the lower shaft ring is in

line with the projection of the feed lifting cam.

The setscrew B should be at the position as shown.

3. Check the clearance between the feed lifting cam

and feed lifting cam spring

When the feed lifting cam is pushed to the left, the

feed lifting cam spring should covered with the feed

lifting cam completely.

If the feed lifting cam does not move smoothly,

adjust as follows:

1. Loosen the setscrews A and B.

2. Bring the needle bar at the lowest position and turn

the lower shaft ring slightly to twist the coil spring

lightly. Set the setscrew A in line with the projection on

the feed lifting cam and tighten it.

3. Tighten the setscrew B

4. Check following the steps 1 to 3 above.

5. Make sure that the lower shaft does not have a play.

Attach the base.

Projection of feed lifting cam

Projection of feed

lifting cam

Setscrew A

Setscrew B

Feed lifting cam spring

Setscrew A

Setscrew B

Projection of feed

lifting cam

Range of turning the

lower shaft ring

Содержание Elinita EF72















































Результаты поиска

Содержание Elinita EF72

Отзывы:

Похожие инструкции для Elinita EF72

Бренды по названию

Популярные бренды

ELNA Elinita EF72, Руководство по обслуживанию

Результаты поиска

Содержание Elinita EF72

Отзывы:

Похожие инструкции для Elinita EF72

Бренды по названию

Популярные бренды