Elmi CM-50 Скачать руководство пользователя страница 9

General information

 

8

 

3

Safety features

Service personnel are prohibited to:

•     

Plug the devie in to a power outlet with configuration that differs from the power adapters  

    configuration.

  Use the device with damaged adapter, power cord, rotor aerodynamic lid or housing.

  Move the device during centrifugation.

  Run the unit without rotor aerodynamic lid or housing.

• 

 Load the rotor asymmetry.

  Use damaged tubes.

ATTENTION! Studied Samples may contain pathological material, including pathogens of 
serious diseases. 

Disinfection and cleaning

Before you start disinfection or cleaning make sure the power adapter is unplugged. It is 

recommended to perform cleaning with water and universal washing liquids. Afterwards the 
machine should be carefully dried. Do not let the water get inside the centriguge.

Transportation and storage

   To insure safety during the transportation, transported equipment should be packed in the 
original manufacturers packaging or similar packaging substitute.
Equipment can be transported by any kind of closed transport make sure that equipment is 
tightly fixed and transportation runs accordingly to regulations applied to this way of transport. 
Equipment should be stored in original manufacturers packaging in dry room with humidity not 
more then 80% and temperature range from +10 C up to +40 C. It is not recommended to store 
the equipment more then 36 month.

Warranty statements

Warranty applies to 24 month period from the date of purchasing.

Malfunctions arisen by the fault of manufacturer during warranty period, are  removed free of 
charge.

Warranty is is not valid in the following cases:

- If the serial number label of the manufacturer is damaged.
- If damages appears as a result of the incorrect operation, transportation or storage.

These documents are necessary if applying for warranty repair:

- User manual with serial number of the machine.
- Officially signed report, describing the reasons and conditions of equipment malfunction.

Warranty repair could be performed only if the equipment is delivered in the original 
manufacturers packaging or equally safe packaging. Therefore please save the packaging 
after unpacking the device.

If the above warranty requirements are disturbed, repair charges are applied to the 
consumer. 

For all further questions concerning exploitation and maintenance please contact 
manufacturer or product vendor.

Содержание CM-50












Отзывы: