background image

 

 

Technical Support: +44(0)23 9269 6638 (option 3) 

 

PAK200790_02A Oct 2019                        ©2019 ELMDENE INTERNATIONAL LTD  

16.

 

Connect the load (output) wiring as shown here. Cable tie to fixing point provided (adjacent to exit 
hole).  

17.

 

If only one load is connected, the PSU will continue to monitor both outputs 

Warning: do not overload the PSU, the ImaxA and ImaxB value is shared between both outputs 

 

18.

 

Re-apply mains. Verify the following 

 

LED # 

Symbol 

LED Colour

 

Function

 

Mains 

Constant Green 

Indication: Mains supply = OK 

Batt 

Constant Yellow 

Indication: Battery Fault = missing battery indicated

 

Fault 

Yellow FLASH x1 

(repeating) 

Indication: Fault with PSU = due to missing battery 

Diagnostic 

Red FLASH x2 (repeating) 

Indication: Fault = missing battery indicated 

OP1* 

Constant Green 

Indication: Output 1 = OK 

OP2* 

Constant Green 

Indication: Output 2 = OK 

 

19.

 

If connected, verify that the EPS Fault monitor shows a (com to n/c) 

CLOSED

 contact and the GEN PSU 

Fault monitor shows an (com to n/c) 

OPEN

 contact. 

20.

 

Perform a full functional test of the connected system (load) including full alarm condition, then 
disconnect the mains supply. 
 

Battery Charger 

21.

 

Set the correct charger mode by fitting the jumper to the appropriate charger mode header.  
Use the table below to select the appropriate charger mode 

 

EN54-4 

Continuous Output Current 

No charging (

Imax B

With Charging (

Imax A

)) 

 
 

1.35 A  

 (b) 1.0 A 

Constant current charge 

0.35 A 

EN12101-10 (ImaxB) 

For 180s at end of standby period

 

1.35 A 

Battery Capacity (2x 12V) 

1.2Ah

 

2.1Ah

 

7Ah

 

EN12101-10 Max 

Standby current

  

(Imax Standby)

 

4hr standby 

0.19A 

0.35A 

1.10 A 

24hr standby 

Not Specified 

0.80 A 

(a) 0.25 A 

72hr standby 

Not Specified 

Not Specified 

0.10 A 

 
 
 
 

a.

 

EXAMPLE (a):

  for EN12101 AOV systems, an 2401ST, with 2x 7Ah batteries, can maintain 

250mA

 load for 

24hrs

 and will be able to deliver 

1.35A

 (ImaxB) for 180s at the end of that 

period 

 

b.

 

EXAMPLE (b):

 for EN54 Fire systems, an 2401ST, with 2x 2.1Ah batteries, can support a 

maximum of 

1.0A

 (ImaxA) load whilst charging the batteries 

 
 
 
 
 
 
 
 

 

Содержание 2401ST


























Отзывы: