background image

iii

FOREWORD

Note:

  This Manual, P/N 98613000, is to be used by qualified and trained personnel, knowledgeable 

of 

NFPA standards and any other applicable standards in effect.

This Manual is intended to provide guidance to qualified technical professionals for the 

installation, operation and maintenance of the HydroBlast™ Intelligent Mining washdown 

cannon system.

Only qualified persons experienced and trained in the installation of this type of equipment 

should install and configure the HydroBlast. They must be familiar and experienced with 

the wiring diagrams and components,electrical installation, and familiar not only with NEC, 

relevant NFPA and local codes but also trained and qualified by Elkhart Brass Manufacturing 

Company, Inc (a Safe Fleet Company). Elkhart Brass Manufacturing Company, Inc. is a 

manufacturer of the components that make up the HydroBlast washdown system, and may 

not have the opportunity to visit the sites where the product is installed or intended to be 

installed. It is the responsibility of the professional installer (described above) to properly 

install and configure the systems. Under no circumstances will Elkhart Brass Manufacturing 

Company, Inc. be liable for improper installation or configuration of the systems.

The technical data contained herein is provided for informational purposes only, and should 

not be used as a substitute for professional judgment. Although, Elkhart Brass Manufacturing 

Company, Inc. believes this information to be true and correct, it is published and presented 

without any guarantee or warranty whatsoever. Elkhart Brass Manufacturing Company, Inc. 

disclaims any liability for any use of the data other than as set out in this manual, foreword 

included.

Any questions concerning the information presented in this manual should be addressed to:

Elkhart Brass Manufacturing Company, Inc.
1302 West Beardsley Avenue
Elkhart, IN 46514, USA 
Phone: 1-574-295-8330
www.elkhartbrass.com

Содержание HydroBlast 7100MG EXM2

































Отзывы: