Page 5
2000000557 (Rev. B - 06/22)
LZO8WSN_2A
Operation: Bottle Filler BF12 Control Board Set-Up
VERIFY CONTROL BOARD SOFTWARE
1) To verify the software program of the control board the unit will
need to be shut down and restarted. The chiller (if present) does
not need to be shut down and restarted.
2) The units lower panel must be open to access the power cord and
wall outlet.
3) Shut down the unit by unplugging the power cord from the wall
outlet or switching off the circuit breaker to the unit.
4)
Restart the unit by plugging the power cord back into the wall outlet.
5) Upon start up, the bottle count display will show the software
designation of BF12.
ACCESSING THE PROGRAMMING BUTTON
1) To access the program button
remove the top cover of the bottle-
filler. Remove the two (2) screws holding top cover to bottle-
filler with a 5/32” (4mm) allen wrench. Remove top cover. Do
not discard mounting screws, they will be needed to reinstall the
top cover
after programming operations are completed. The
programming button is located at the top right side of the unit on
the control board.
RESET THE FILTER MONITOR
1) Instructions apply to filtered units only.
2) Depress the program button for approximately 2 seconds until
the display changes then release. The display will change and
scroll through two messages:
“RST FLTR” – Reset Filter Monitor
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
3) When the display changes to “RST FLTR”, depress the button
again. The display will change to show “FLTR =”. Depress the
button again and the display will show “FLTR =0”
4) The Green LED should be illuminated indicating that the visual
filter monitor has been reset.
SETTING RANGE OF THE IR SENSOR WHERE APPLICABLE
1) Depress the program button for approximately 2 seconds until
the display changes then release. The display will change and
scroll through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button
again. The display will change to show
“RNG SET” - Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
“FLT SIZE” - Select filter capacity
“RST BCNT” - Reset bottle count
3) When display shows “RNG SET” push program button once the
display will show current value (can be 1 – 10) e.g. “RNG = 3”.
4) Once display shows current value push the program button to
scroll through value of 1 – 10. Select the desired range setting,
"1" being closest to sensor and "10" being farthest away.
5) Once range is selected allow approximately 4 seconds to pass and
then the display will go back to bottle counter and be in run mode.
6) Test bottle filler by placing bottle or hand in front of sensor to
make sure water is dispensed.
SETTING UNIT TYPE
1) Depress the program button for approximately 2 seconds until the
display changes then release. The display will
change and scroll
through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2)
When the display changes to “SETTINGS”, depress the button again.
The display will change to show
“RNG SET” - Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
Continued from below:
“FLT SIZE” - Select filter capacity
“RST BCNT” - Reset bottle count
3)
When display shows “UNIT TYPE” push program button once the
display will show current value.
Can be REFRIG or NON-RFRG
4) Push button once to change value. Once value is
selected the
display will show the new value.
(Can be REFRIG or NON-RFRG)
“REFRIG“ - stands for refrigerated product. In this setting the flow
rate is estimated at 1.0 gallon per minute (3.8 lpm).
“NON-RFRG“ - stands for non refrigerated product. In this setting the
flow rate is estimated at 1.5 gallons per minute (5.7 lpm). Both
“REFRIG“ and “NON-RFRG“ simulate
1 bottle equal to
20 oz (590 ml).
5)
Allow approximately 4 seconds to pass and the display will return to
bottle counter and be in run mode.
RESETTING BOTTLE COUNT
NOTE: Once the bottle count is reset to zero there is no way to
return to the previous bottle count.
1) Depress the program button for approximately 2 seconds until the
display changes then release. The display will change and scroll
through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button
again. The display will change to show:
“RNG SET”- Range set for IR sensor.
“UNIT TYP” - Type of unit (REFRIG or NON-RFRG)
“FLT SIZE” - Select filter capacity
“RST BCNT” - Reset bottle count
If the button is not pushed again the display will scroll through the
four messages above for three cycles and return to run mode.
3)
When display shows “RST BCNT” push program button once the
display will show current value, e.g. “0033183”.
4) Once display shows current value push the program button once
more to reset back to 0. The display will show BTLCT = 0 for
approximately 2 seconds and then return to run mode showing
00000000 bottles.
5) Testing the bottle counter:
REFRIG units: Place bottle or hand in front of sensor for
approximately 9 seconds to see bottle counter count 00000001,
(This is based on filling a 20 oz (590 ml) bottle).
NON-RFRG units: Place bottle or hand in front of sensor for
approximately 6 seconds to see bottle counter count 00000001,
(This is based on filling a 20 oz (590 ml) bottle).
SETTING FILTER CAPACITY
1) Depress the program button for approximately 2 seconds until the
display changes then release. The display will
change and scroll
through two messages:
“RST FLTR” – Reset Filter Status LED
“SETTINGS” – System Settings Sub Menu
If the program button is not pushed again the display will scroll
through the two messages above for three cycles and then default
back to bottle count and be back in run mode.
2) When the display changes to “SETTINGS”, depress the button
again. The display will change to show:
“RNG SET“ - Range set for IR sensor.
“UNIT TYP“ - Type of unit (REFRIG or NON-RFRG)
“FLT SIZE” - Select filter capacity
“RST BCNT“ - Reset bottle count
If the button is not pushed again the display will scroll through the
four messages above for three cycles and return to run mode.
3)
When display shows “FLT SIZE” push program button once. The
display will show current value. Can be 3000GAL or 6000GAL.
4) Push program button again to display the desired “FLT SIZE”.
5) Allow approximately 4 seconds to pass and the display will return to
bottle counter and be in run mode.
