Elka KOMET 200 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 47

Elka KOMET 200 Скачать руководство пользователя страница 39

KOMET 200 - 600

Display Corresponds

to:

S1

Pressure relief for electromagnetic bolt is deactivated.

S2

The gate wing pushes slowly (500ms min., but 1000ms max.)
against the end stopper until the selected force is reached.

S3

The gate wing pushes slowly (500ms min., but 2000ms max.)
against the end stopper until the selected force is reached.

S4

The gate wing pushes slowly (500ms min., but 90s max.)
against the end stopper until the selected force is reached.

Table 23

10.3.1.13

Sequence PD: Wind blast suppression

It can be chosen to either reverse on obstacle immediately, or to reverse after
a preset time. When setting a time, a short wind blast or an oscillating gate
wing do not result in a stop (and reversal).

ATTENTION! Only use the wind blast suppression, when additional
safety devices like photo-cells and safety contact profiles are installed at
the gate.

When sequence

PD

is activated by

button LERN

, the present selection is

displayed. With the

button BT

the value can be selected (see table). Return to

the learning sequence using

button LERN

.

Display Corresponds

to:

u-

No wind blast suppression. The controller immediately reacts
on obstacle/wind blast.

u1

bis

u9

The wind blast suppression equals 1s (for U1) up to 9s (for
U9). The controller reacts on obstacle / wind blast only after
the selected time1s (for U1) up to 9s (for U9).

Table 24

10.3.1.14

Sequence PE: Multi-functional relay

The multi-functional relay on the controller is suitable for four different modes.
During learning function the relay is inactive.
When sequence

PE

is activated by

button LERN

, the present selection is

displayed. With the

button BT

the value can be selected (see table).

Return to the learning sequence using

button LERN

.

Display Corresponds

to:

r1

Push button mode: The relay is active as long as the
controller receives the radio remote control code MULTI.

r2

Toggle mode: The relay alternates between active and
deactive with each radio remote control code MULTI.

r3

Light pulse mode: The relay is active for 1 second, when BT,
FunkBT, BTG, Funk BTG, BA or BZ are pushed.

r4

3-minute light: The relay is active for 180 seconds, when BT,
FunkBT, BTG, Funk BTG, BA or BZ are pushed.

Table 25

38

«
...
37
38
39
40
41
...
»

Содержание KOMET 200
















































Отзывы:

Нет отзывов