manualshive.com logo in svg

Eliwell EWCM 4120, Руководство пользователя, Страница: 57 / 75

Поделиться
Скачать
Eliwell EWCM 4120 Скачать руководство пользователя страница 57

 

57 

Code Action 

Notes 

Er19 
Er20 
Er21 
Er22 
Er23 

Message 

Alarm condition reset by zeroing the number, operating time 
and resetting the alarm. If Cp17=0 management alarm disabled. 

Er24 
Er25 
Er26 
Er27 
Er28 

Message 

Alarm condition reset by zeroing the number, the running time 
and resetting the alarm. If Fn19=0, management alarm disabled. 

Er29  Blocks the system 

  

Er30 

Operation of compressor regulator from 
CP21. 

Management of inlet analogue maximum and minimum alarms 
disabled. Inlet pressure switch response alarm signalled as low 
pressure alarm. 

Er31  Operation of outlet regulator from FN24. 

Management of outlet analogue maximum and minimum 
analogues alarms disabled. Outlet pressure switch response 

alarm signalled as low pressure alarm. 

Er33 
Er34 

Message 

Reset alarm by resetting the clock with current 

day/hour/minute and switching off/restarting. 

Er35  Blocks the system 

Signalled at power-on of the device or a parameter has been 
modified 

Er37  Message 

If AL25=0, alarm disabled. Reset with log deletion 

 

Содержание EWCM 4120












































































Отзывы:

Нет отзывов